updated!
CompMan - NJ Reckoning - VA HellHammer - FL xpingux - Ontario NSrobbie - Ontario edblor - Ontario chelecuche - CA steveard - Vancouver, Washington brandirena86 - Meridian, ID |
I remove myself from the list...
Updated: CompMan - NJ Reckoning - VA HellHammer - FL xpingux - Ontario NSrobbie - Ontario edblor - Ontario steveard - Vancouver, Washington brandirena86 - Meridian, ID |
I'mma send it to you anyway :)
|
when the program says searching for board it never finds it. I tried with the ignition on and off.
Anyone have the same problem? |
You need to disconnect from the car before plugging in the update cable.. As long as the box is unpowered, it will work.
|
I need this cable I'm in Mass. My time comes up wrong.
is there somewhere I can buy this if I dont end up wanting to wait? |
Cable arrived today. Getting mailing address for next person, and with luck it'll be gone tomorrow.
|
I remove myself from the list...Thanks again. Send to xpingux
Updated: CompMan - NJ Reckoning - VA xpingux - Ontario NSrobbie - Ontario edblor - Ontario steveard - Vancouver, Washington brandirena86 - Meridian, ID |
xpingux - Ontario
NSrobbie - Ontario edblor - Ontario steveard - Vancouver, Washington brandirena86 - Meridian, ID Ontario time :cool: Getting address from xpingux |
add me to the list please.
Does the firmware update solve that a/c issue? Or is mine a soldering issue? if it is can someone direct me to the thread? Sometimes when I turn the knob from hot to cold, it doesn't click over, I have to do it a few times, also my AMB TEMP is never right. Or do I have a bigger problem? PHX, AZ Also, how do you check your firmware on your axxess box? |
Added
xpingux - Ontario
NSrobbie - Ontario edblor - Ontario steveard - Vancouver, Washington brandirena86 - Meridian, ID Rxster - Phoenix, AZ |
Originally Posted by Rxster
(Post 3681093)
add me to the list please.
Does the firmware update solve that a/c issue? Or is mine a soldering issue? if it is can someone direct me to the thread? Sometimes when I turn the knob from hot to cold, it doesn't click over, I have to do it a few times, also my AMB TEMP is never right. Or do I have a bigger problem? PHX, AZ Also, how do you check your firmware on your axxess box? https://www.rx8club.com/series-i-do-yourself-forum-73/diy-no-heat-repair-heater-control-158200/ |
Aswc
I sent the cable on the 20th. It should arrive within the next two days if I'm not mistaken. Sorry for the delay,as for my aswc, im pretty sure its fried, i tried it with a different head unit and it was even less responsive. It just wont output the correct signal, if any at all. And yess I checked the wiring and yess I manually reprogrammed it, but to no avail. I ordered a new aswc from an authorized distributor this time, hopefully it'll work.
|
You can take me off the list
I was able to find another cord so I am up and working. Please take me off the list.:)
|
What was wrong
I tried the axxess cable and it didn't work so I ended up buying a new aswc.
Symptoms: When it auto programed, only two buttons would work, and they don't do what they're supposed to do. The next button would change modes and the mode button would skip tracks. No change after manual programming. When used with a different head unit, the head unit wasn't receiving response from the aswc=> nothing. if you have similar symptoms look here: https://www.rx8club.com/showthread.p...50#post3679350 |
List Update
|
Can I get added to the list?
Been living with no A/C in Orange County way too long. Orange County, CA |
After being a dick and having it for far toooooo long, I'm sending it to NSrobbie asap.
Also, the firmware version is now 1.5. That is all. |
what do I have to do to get on the cable list?
|
xpingux - Ontario
NSrobbie - Ontario edblor - Ontario brandirena86 - Meridian, ID lynchy803 - MA Rxster - Phoenix, AZ fireflypulse - Orange County, CA i0nicx - Outer Space omg u just maed it 2 teh listlol. (Where are you from, boy?) |
I'm sure it has been asked. I am getting ready to buy the kit, should i add myself to the list now? Will I need to at all? Thanks in advance!
|
im in levittown, ny(long island)
|
just received the cable today (thanks xpingux) will get the update done asap
|
update complete... finally have a functioning clock lol.
msged edblor for address. |
Cable has been shipped to edblor
edblor - Ontario brandirena86 - Meridian, ID lynchy803 - MA Rxster - Phoenix, AZ fireflypulse - Orange County, CA i0nicx - levittown, ny(long island) |
All times are GMT -5. The time now is 09:19 AM. |
© 2024 MH Sub I, LLC dba Internet Brands