Notices

In dash Sirius Head Unit Project

Thread Tools
 
Rate Thread
 
Old Aug 29, 2009 | 11:10 PM
  #1  
john15509's Avatar
Thread Starter
Registered
 
Joined: May 2009
Posts: 14
Likes: 0
In dash Sirius Head Unit Project

Decided I would try something new with the interior and I was tired of having my stupid sirius radio hanging off my window so I got a idea and here are the photos from my project. Took me about 8 hours over the span of 2 weeks to finish. I used a dremel tool to cut the plastic. Pictures arent the best of quality since they were taken by my phone.

Picture of interior when I first got the car (only about 3 months ago) but pre-installation

I ordered a new entire ashtray compartment and started to take out the lighter plug and all the extra plastic

The sirius head unit sat on this, it had to be taken apart because it would not have fit, so I took the cover off and just retrieved the inserts for the radio.

Last edited by john15509; Aug 29, 2009 at 11:30 PM.
Reply
Old Aug 29, 2009 | 11:20 PM
  #2  
TheBurkeMan's Avatar
Registered
 
Joined: Oct 2008
Posts: 322
Likes: 0
From: LaVergne, TN
the pics dont work
Reply
Old Aug 29, 2009 | 11:29 PM
  #3  
john15509's Avatar
Thread Starter
Registered
 
Joined: May 2009
Posts: 14
Likes: 0
This is the head unit holder disassembled


I started cutting out the hole for the head unit here



Started to put black foam around the edges to make a neater finish rather than my half *** sand job (which I did not want to try)


Reply
Old Aug 29, 2009 | 11:35 PM
  #4  
john15509's Avatar
Thread Starter
Registered
 
Joined: May 2009
Posts: 14
Likes: 0
Here is the head unit inside the lid after foam was installed. Dont have picture but I got rid of all that glossy/white residue from the glue afterwards



This is the backview of what the head unit + the lid



Whew , this is a ugly picture but I just pulled off the panel over the stick shift and just removed the orginal ashtray



This is after the install, its night time and I just wanted to take a picture to show off what I could, tomorrow Ill take a picture during daytime

Reply
Old Aug 30, 2009 | 10:07 PM
  #5  
john15509's Avatar
Thread Starter
Registered
 
Joined: May 2009
Posts: 14
Likes: 0
Reply
Old Aug 30, 2009 | 10:10 PM
  #6  
shakeyourbrakes's Avatar
Registered
iTrader: (4)
 
Joined: Oct 2007
Posts: 736
Likes: 1
From: Northern, VA
looks good, whats with the foam? id try and remove that excess, or at least bondo the whole cover smooth.
Reply
Old Aug 31, 2009 | 04:54 AM
  #7  
john15509's Avatar
Thread Starter
Registered
 
Joined: May 2009
Posts: 14
Likes: 0
Just something temp. to go over the unsanded edges. Im going to replace the lid soon because its got some scratches that doesnt make it took to pleasing upclose
Reply
Old Aug 31, 2009 | 11:31 AM
  #8  
StormyWankel's Avatar
EVOLVChicago.org
 
Joined: Aug 2009
Posts: 200
Likes: 0
From: Palatine, IL
i should try this with my Sportster 5...how do you have the power run? I have seen hardwire kits on eBay and wondered if thats what you used...
Reply
Old Aug 31, 2009 | 05:14 PM
  #9  
MrAdam5's Avatar
Registered
 
Joined: May 2009
Posts: 206
Likes: 0
From: Lethbridge, Alberta, Canada
Just curious, where did you order the extra ashtray compartment from and how much? This was something I was looking to do but was going to cost me $200+ for a custom piece and didn't want to cut up my original ashtray in case I wanted to revert. So if I can get a new ashtray at something less than 200 I may attempt this myself.
Reply
Old Aug 31, 2009 | 06:40 PM
  #10  
john15509's Avatar
Thread Starter
Registered
 
Joined: May 2009
Posts: 14
Likes: 0
I just un attached the cigeratte lighter from the ashtray compartment and plug my power cord into it and put it behind the ashtray comparment when I installed it.

MrAdam5 I got it for 30 bucks shipped from user MAZMART "6"
Reply
Old Dec 31, 2009 | 10:12 PM
  #11  
A.Mair's Avatar
Registered
 
Joined: Mar 2007
Posts: 1,623
Likes: 1
From: Vegas
do you have a link for that John? i just got the same sirius headset and want to do something like this
Reply
Old Jan 1, 2010 | 01:17 AM
  #12  
Alexb's Avatar
desperately needs a drop
iTrader: (1)
 
Joined: Sep 2008
Posts: 1,127
Likes: 1
From: Dallas, Texas
I kinda want to do a similar mod, only take the whole tray out, just make it one big compartment so I can actually have a place to put my phone... but still keep the door.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jazzmeson
RX-8 Multimedia/Photo Gallery
11
Mar 2, 2016 02:25 PM
ShellDude
RX-8 Parts For Sale/Wanted
5
Oct 1, 2015 09:55 PM
FubarI33t
New Member Forum
12
Sep 28, 2015 08:45 PM
Stubbs
Series I Wheels, Tires, Brakes & Suspension
0
Sep 27, 2015 04:06 PM
drlubell
RX-8's For Sale/Wanted
0
Sep 26, 2015 11:58 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -5. The time now is 01:07 AM.