V-LEDs Tail Light Star Design
Has anybody tried these LEDs? Will they fit in the factory light housing?
V-LEDs White V-Star M-SMT Parking Lights |
Pico has them in his brake lights
https://www.rx8club.com/series-i-exterior-appearance-body-kits-27/v-led-upgrade-brake-signal-lights-169490/ |
I notice that the stock bulbs are not tinted red. Is it safe and reasonable to use white LED taillights to provide a brighter glow while the red enclosure will still provide the red tint.
|
Originally Posted by bmak
(Post 3346898)
I notice that the stock bulbs are not tinted red. Is it safe and reasonable to use white LED taillights to provide a brighter glow while the red enclosure will still provide the red tint.
|
my friend jose has them on his shinka and they look super hoTTTT, get them.!
|
1 Attachment(s)
I've had them since last winter and they are 10times brighter then the OE lights.
IMO worth the price. If I were you i would stick with the red LED Attachment 268181 |
Pico: any night time pics?
any draw backs to swapping out to these LED's? Is it the brake lights that freak out the abs system for some people? Rev: isn't that what happened to RedFox? |
2 Attachment(s)
Originally Posted by Jedi54
(Post 3347060)
Pico: any night time pics?
any draw backs to swapping out to these LED's? Is it the brake lights that freak out the abs system for some people? Rev: isn't that what happened to RedFox? the amber turn signals are V-Led AMBER 1157 V-LEDS 7W HIGH POWER 20 LED TURN SIGNAL BULBS 2057 Attachment 268179 Attachment 268180 |
Originally Posted by Jedi54
(Post 3347060)
Pico: any night time pics?
any draw backs to swapping out to these LED's? Is it the brake lights that freak out the abs system for some people? Rev: isn't that what happened to RedFox? Installing a resistor in the 3rd brake light solves the problem if you have all LEDs |
1 Attachment(s)
I also have the LED 3rd brake light that isn't shown in the pics above. I 'm not using a resistor on the 3rd brake light and there are no problems to report .
Only resistors being used are two 3ohms for the rear turn signals. Here's a full view Attachment 268178 |
Interesting, although to my knowledge the problem occurs when the 3rd brake light is replaced with a 7440 LED. Your fancy schmancy LED board must be different :)
|
Bingo
There's your problem |
Pico, is that 3rd brake light one of the ones available on ebay? Been looking for a good 3rd brake light as well, what do you think of the one you have there?
|
Pico, I like the look of the turn signals as well, but I'm not sure about double the price for the "high power" ones, anybody have any experience with the standard amber turn signals and the standard white back up lights? I presently have the tail-light kit from rotaryfx and i'm disappointed with the results.
|
Originally Posted by bmak
(Post 3347468)
Pico, is that 3rd brake light one of the ones available on ebay? Been looking for a good 3rd brake light as well, what do you think of the one you have there?
Originally Posted by bmak
(Post 3347472)
Pico, I like the look of the turn signals as well, but I'm not sure about double the price for the "high power" ones, anybody have any experience with the standard amber turn signals and the standard white back up lights? I presently have the tail-light kit from rotaryfx and i'm disappointed with the results.
the OE and FX lights are very under power. I have had the FX lights in the past and they definitely not worth the money. |
What about the V-LEDs standard (I already know too well to avoid the rotaryfx ones). Here's a link: V-LEDs M-SMT 27 LED Amber.
And the same for white backup lights: V-LEDs M-SMT 27 LED White. |
|
Originally Posted by bmak
(Post 3347548)
What about the V-LEDs standard (I already know too well to avoid the rotaryfx ones). Here's a link: V-LEDs M-SMT 27 LED Amber.
And the same for white backup lights: V-LEDs M-SMT 27 LED White. Definitely not as bright as the 7w bulbs but they still would be a good upgrade |
I've seen the ones on sale on eBay and was wondering if they'd require a resistor.
|
They dont need resistors. I have all my brake lights replaced with LEDS and they work fine. However, if you want to change the indicator lights to prevent hyper flashing I think you will need resistors.
|
No resistor for 3rd brake light -- if you buy the actual light
3-6 ohm resistors for the signals are a must if you want to prevent hyper flashing. |
All times are GMT -5. The time now is 11:38 AM. |
© 2024 MH Sub I, LLC dba Internet Brands