How To Remove Headlights?!?!
#1
Outta My Way!!!
Thread Starter
Join Date: Mar 2006
Location: South Lyon,MI
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
How To Remove Headlights?!?!
I was installing my new parking light led's and when I got the driver side in, all the wigglin that I did to get it in caused the led to fall off in the housing. I searched for headlight removal and such but couldnt find anything. Please help I need to get it done before dark falls.
#2
Banned
iTrader: (3)
Pull the front bumper. Its the only way.
There are about 10 8mm bolts along the lower front edge, 8 plastic clips inside each fender well on the trailing edge of the bumper, two screws that hold the marker lights and 4 10mm bolts on the upper rad support under the plastic cover. Disconnect your fog lights (if you have them) and pull.
Then the headlamps are held in with 4 or 5 10mm bolts each.
The whole job takes me about 1/2 hour, but YMMV.
There are about 10 8mm bolts along the lower front edge, 8 plastic clips inside each fender well on the trailing edge of the bumper, two screws that hold the marker lights and 4 10mm bolts on the upper rad support under the plastic cover. Disconnect your fog lights (if you have them) and pull.
Then the headlamps are held in with 4 or 5 10mm bolts each.
The whole job takes me about 1/2 hour, but YMMV.
#3
I "tried" to install new parking lights and they're a bitch to get to.
I have to pull the bumper off this weekend to do some other mods so
I'll take a few pictures for you.
EBF
I have to pull the bumper off this weekend to do some other mods so
I'll take a few pictures for you.
EBF
#7
Outta My Way!!!
Thread Starter
Join Date: Mar 2006
Location: South Lyon,MI
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
Well I found my way around it. I have a small magnetic rod that I put in there and it latched onto the led with no problem so I finally got it out.
#9
Registered User
Join Date: Mar 2005
Location: Southern CA
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 2Xrotary
Well I found my way around it. I have a small magnetic rod that I put in there and it latched onto the led with no problem so I finally got it out.
#19
Registered User
Join Date: Mar 2004
Location: Vancouver
Posts: 1,501
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MazdaManiac
Pull the front bumper. Its the only way.
There are about 10 8mm bolts along the lower front edge, 8 plastic clips inside each fender well on the trailing edge of the bumper, two screws that hold the marker lights and 4 10mm bolts on the upper rad support under the plastic cover. Disconnect your fog lights (if you have them) and pull.
Then the headlamps are held in with 4 or 5 10mm bolts each.
The whole job takes me about 1/2 hour, but YMMV.
There are about 10 8mm bolts along the lower front edge, 8 plastic clips inside each fender well on the trailing edge of the bumper, two screws that hold the marker lights and 4 10mm bolts on the upper rad support under the plastic cover. Disconnect your fog lights (if you have them) and pull.
Then the headlamps are held in with 4 or 5 10mm bolts each.
The whole job takes me about 1/2 hour, but YMMV.
Whoa whoa whoa guys.... no need to take off the bumper or remove the headlights at all........
1) Jack up the front of the car
2) Remove the 3-4 tabs of the fender liner behind the headlight area
3) Pull back the fender liner plastic
Voila you have full access to the back of the headlights...
LAMO
#20
zoom fuckin zoom
Join Date: Sep 2008
Location: PA, USA
Posts: 386
Likes: 0
Received 0 Likes
on
0 Posts
Whoa whoa whoa guys.... no need to take off the bumper or remove the headlights at all........
1) Jack up the front of the car
2) Remove the 3-4 tabs of the fender liner behind the headlight area
3) Pull back the fender liner plastic
Voila you have full access to the back of the headlights...
LAMO
1) Jack up the front of the car
2) Remove the 3-4 tabs of the fender liner behind the headlight area
3) Pull back the fender liner plastic
Voila you have full access to the back of the headlights...
LAMO