E-Manage Profec E-01
#29
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
I ve purchased with the profec e0-1 a harness that it says that it connects on the signal...but it has a connector only from the one side..THe wires from the other side are naked..They need to cut and paste to the emanage harnesses maybe..Is this optional???where do i need to cut paste etc???offcourse i have a greddy turbo.. :D
#30
Ex- member.
I currently have the Profec B spec II but I'm switching it out with the E-01 so I can hold 7psi throughout the RPM range. There's a couple of things when installing the E-01 with the Greddy turbo kit.
- You will need to send in your SD memory card to Benny at Greddy USA so he can update it and have it work with the RX8 emanage.
- Buy the Pressure Sensor harness found on this page for $20.
You disconnect the pressure sensor that's hooked up to the emanage now and connect it to the E-01, then install this cable from the E-01 to the emanage. Yes, you will have a left over pressure sensor.
- Buy a USB A/B cable like this one $5, found on the same site or any computer store. This enables the E-01 and emanage to talk to each other (upload/ change maps).
The rest of the install is pretty straight forward except for the RPM signal wire (brown) on the E-01 power harness.
I talked to Benny and he said it connects to the brown wire on the RPM dongle (it's the bottom one in the picture, ends in 3).
Also, I've installed mine where Jeff did and routed the wires through the unused airbag plastic cover. I used my old cell phone holder as the base, it's $30 and found here. The E-01 bracket screwed in perfectly with the base holes and I can still access all the radio buttons and open the glovebox.
Pictures below. Also, I'm going to put the wired remote on the bottom portion of the bracket. Test fitted and looks like it'll fit.
I still need to remove my Profec B spec II and put it on ebay and buy a new radio trim piece.
- You will need to send in your SD memory card to Benny at Greddy USA so he can update it and have it work with the RX8 emanage.
- Buy the Pressure Sensor harness found on this page for $20.
You disconnect the pressure sensor that's hooked up to the emanage now and connect it to the E-01, then install this cable from the E-01 to the emanage. Yes, you will have a left over pressure sensor.
- Buy a USB A/B cable like this one $5, found on the same site or any computer store. This enables the E-01 and emanage to talk to each other (upload/ change maps).
The rest of the install is pretty straight forward except for the RPM signal wire (brown) on the E-01 power harness.
I talked to Benny and he said it connects to the brown wire on the RPM dongle (it's the bottom one in the picture, ends in 3).
Also, I've installed mine where Jeff did and routed the wires through the unused airbag plastic cover. I used my old cell phone holder as the base, it's $30 and found here. The E-01 bracket screwed in perfectly with the base holes and I can still access all the radio buttons and open the glovebox.
Pictures below. Also, I'm going to put the wired remote on the bottom portion of the bracket. Test fitted and looks like it'll fit.
I still need to remove my Profec B spec II and put it on ebay and buy a new radio trim piece.
Last edited by adrian-1; 07-07-2005 at 09:05 PM.
#31
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
The first step...Sending the sd memory to benny is optional????I live in Greece for God...another step back....
Do you believe Greeddy Greece can make it work??They are new in the bussiness
Do you believe Greeddy Greece can make it work??They are new in the bussiness
#32
Ex- member.
I'm sure Greddy Greece can get it done. I only put Greddy USA cause that's who I'm going through and most other people will too.
All they have to do is update the E-01 using the SD card to version 1.42
All they have to do is update the E-01 using the SD card to version 1.42
#33
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
i don't see why this step is needed as the map is locked so why updating??anyway i ll give them a call on Monday...This was my last problem...I am running very rich with the stock cat..I ll try again with the high flow cat and if i c arround 12 i ll keep it on...
Thanks for the great post adrian..# 30!!! :D
Thanks for the great post adrian..# 30!!! :D
#37
90% Carbon-100% Power
Join Date: Apr 2004
Location: Thessaloniki,GREECE
Posts: 1,706
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys where do you connect the signal harness...Where do you need to cut the wires of the emanage to paste the harness and take the advantages of seeing in profec afr etc????Please this is the only thing left right now...
#39
Banned
iTrader: (3)
Originally Posted by GrRx8MaZdA
Hey guys where do you connect the signal harness...Where do you need to cut the wires of the emanage to paste the harness and take the advantages of seeing in profec afr etc????Please this is the only thing left right now...
That is for bringing in external signals into the Profec. If you have a wide-band O2s, you can set it up to send a voltage to the Profec through that harness.
Thread
Thread Starter
Forum
Replies
Last Post
yurcivicsux
Series I Major Horsepower Upgrades
192
09-12-2017 10:54 PM
RicerX1
West For Sale/Wanted
5
01-11-2016 05:59 PM
05rx8mazda
RX-8 Parts For Sale/Wanted
18
11-28-2015 09:42 AM
Neo_Genisis_D
Series I Aftermarket Performance Modifications
0
07-11-2005 04:31 PM