DIY: How to change your rear brake pads.
#76
Registered Zoom Zoomer
iTrader: (2)
The only thing I will add is that you'll probably find the two Phillips head screws on each of the front rotors to be very difficult to remove. But an inexpensive hand impact driver will handle them in short order. When replacing, use some anti-seize paste on their threads (but of course Not on the wheel lugs).
Impact driver: http://www.harborfreight.com/cpi/cta...emnumber=37530
The rear rotors are just held on by the wheel lugs.
Impact driver: http://www.harborfreight.com/cpi/cta...emnumber=37530
The rear rotors are just held on by the wheel lugs.
The following users liked this post:
Falkian (06-01-2021)
#78
Registered
iTrader: (6)
Just did my rear brakes today and had a bit of trouble in lining up the +, eventually i got it on but the top caliper was really snug and i had to use some force to get it on.
Is it possible to have everything reassembled and the nipple in the correct location and it be too tight? as in not enough clearance...? Ive only driven it a few miles and i ddnt really notice any problems but my rotor is starting to turn a bit brown...
Is it possible to have everything reassembled and the nipple in the correct location and it be too tight? as in not enough clearance...? Ive only driven it a few miles and i ddnt really notice any problems but my rotor is starting to turn a bit brown...
#79
Registered
iTrader: (1)
Join Date: May 2006
Location: SoCal
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
If your not experiencing any issues that might be just the transfer material from the brake pad during your initial break in or "bedding in" time. Have you heard of the procedure? The brake bedding in procedure is somewhere on this site I'm sure you'll find it if you search.
#82
i am in the middle of doing my rear pads..... and for the life of me the piston will not turn in.... Ive been turning it clockwise for about a hour with some needle nose pliers. please help for i am about out of ideas. thanks in advance
#84
yes brake fluid cap is open. i am giving up until tomorrow to go get a tool... thanks for the quick response.
#89
Registered
iTrader: (2)
Join Date: Oct 2007
Location: Pacific Northwest
Posts: 16,684
Likes: 0
Received 240 Likes
on
110 Posts
Alright, I'm on my driver's rear side doing the pad change, and I'm turning the piston, maybe 60 1/4th rotations so far, or ~15 full rotations, and I swear the piston hasn't gotten any farther back. Does it just have insanely tight thread pitch?
#90
Registered
iTrader: (2)
Join Date: Oct 2007
Location: Pacific Northwest
Posts: 16,684
Likes: 0
Received 240 Likes
on
110 Posts
Ok, they are farther back than they were, I put the old pads on just to check to see if I made any progress, and I have. But when compared with the new pads, it is still just to the edge of the backing, not past it yet, and it's not going back any further. Rotating plenty, but not going back. Even with pressure. Brake fluid cap is off (well, off, then I set it back on top, not threaded or anything, just to keep junk from floating in).
Can't figure out why. Still maybe 1/4th of an inch to go before it's flush with the caliper. OEM pads from Mazmart....
Can't figure out why. Still maybe 1/4th of an inch to go before it's flush with the caliper. OEM pads from Mazmart....
#92
I just did this tonight. When I put the new pads in place, I could not get the caliper to fit when the anti-rattle clips in place. I had to leave them out for now and I'll put them in after about 5,000 miles when the brakes have worn down a little to give extra room.
The rear driver's brake piston would not compress past a certain point. I had to loosen it all the way and then start over with the clockwise/compress to get it all the way down.
The rear driver's brake piston would not compress past a certain point. I had to loosen it all the way and then start over with the clockwise/compress to get it all the way down.
#93
Charles Bundy
iTrader: (5)
Also remember, your initial step should be extracting at least 15 cc's of the brake fluid from the reservoir to prevent overflow before installing new brake pads. As we all know, brake fluid is damaging to paint.
Last edited by Grace_Excel; 10-19-2010 at 02:24 PM.
#94
Super Moderator
Wouldn't is be much "easier" if one cracks off (opens) the Bleeder Nipple on Caliper?..
Yes, you have to catch Brake Fluid at Caliper.
Yes, you have to bleed system at finish.
BTW: this side of the world we call them G Clamps, not C.
Yes, you have to catch Brake Fluid at Caliper.
Yes, you have to bleed system at finish.
BTW: this side of the world we call them G Clamps, not C.
#95
Charles Bundy
iTrader: (5)
That would have been my initial, but I went ahead and tried using the "G-Clamp", as you would say. Eventually, when it loosed, I could turn the piston itself with both of my index and thumb fingers to clear the new pads.
Do any of you know how to adjust the lines for the E-brake? I parked my car on our inclined driveway, pulled the E-brake (gear's in neutral) as I normally have; came out half-an-hour later and my car's on the street! For some odd reason, I have to really pull the E-brake back.
Do any of you know how to adjust the lines for the E-brake? I parked my car on our inclined driveway, pulled the E-brake (gear's in neutral) as I normally have; came out half-an-hour later and my car's on the street! For some odd reason, I have to really pull the E-brake back.
Last edited by Grace_Excel; 10-19-2010 at 09:27 PM.
#96
Stuck in a love triangle
Changing the rear pads on this car is such a friggin pain in the ***. I say you should just lay down the dough and let a mechanic handle this one unless you're a diehard DIYer.
#100
Project Seca
iTrader: (10)
just changed my break pads as my rear pads were worn down. i might say great DIY! i must note though (im not sure if it has already been noted), some breaks with shims/spacers/backplates already on they might make fitment too tight, its best to remove them or you could damage your breaks/rotor.