SARX installs a turbocharged bridge ported renny a picture thread
: Disclaimer, This thread is for pictures only. I would love to hear your comments but all technical discussion can be directed at:
https://www.rx8club.com/major-horsep...thread-210754/ I have personally been working towards this for about two years now. I have only been stateside for about 4 months and have had to update my install timeline by about a month so not all is exactly where I would like it to be and some compromises were made. I hope you enjoy my thread I could not have done this without out the help of: 9krpmrx8, Hector Castillo, shadycrew31, cornholio135, houstonrx8er, Grungepup, Kane Thank you guys for all the support and hard work to make this happen. |
Would like to kick off the thread with a bit of info about the build.
2005 RX8 72K miles. Bridge ported renny with a ton of extra work done by: BDC Motorsports Low Mount turbo kit with some extra work built by: Turblown Modded by Hoss -05 Lots of extras from BHR, the only Carbonitic carbon clutch and diff i know about in the US. Other stuff as well but lets save that for the Tech discussion thread. This is what I see when I wake up in the morning. - a few cars. http://lh3.googleusercontent.com/-Cq...831_081311.jpg The bridge port Renny. http://lh5.googleusercontent.com/--5...831_101039.jpg Check the 50mm dump tube... yikes! http://lh4.googleusercontent.com/-UQ...831_172302.jpg Here you can see the heat shields turblown made for me. They did a Great job. http://lh5.googleusercontent.com/-H1...831_173216.jpg Another picture in this one you can my broke wast-gate. "the nipples are broke alone with the bent adjuster" this a a 50mm unit and will take heat like no other. Its sad it got messed up so bad. http://lh3.googleusercontent.com/-C2...831_173138.jpg Another view... look at all the idmitsu in the back... :P http://lh6.googleusercontent.com/-es...831_173205.jpg |
Rad pack out.
http://lh5.googleusercontent.com/-BU...901_142732.jpg engine out.... thanks guys... you know who you are. http://lh5.googleusercontent.com/-va...901_202713.jpg Old pilot .... wow this think looks crazy.. not sure what to think. http://lh5.googleusercontent.com/-66...901_202917.jpg With S1 tranny. http://lh6.googleusercontent.com/-wX...902_113531.jpg So for this install I decided to go heat shield crazy. This is my quick and simply s2 heat shield. It was left over from other parts. http://lh6.googleusercontent.com/-iF...902_135141.jpg This is the Lower intake manni custom ported by BDC Motorsports and covered by a bit of heat shield by Cornholio135.... I swear corn/Mike is the king of wrapping. Can only imagine what his C-mas presents look like. http://lh4.googleusercontent.com/-X-...902_140632.jpg Here is another pick of my engine by half way through my heat shield install. Its all custom installed by me. with my big turbo i banged the crap out of my fire wall and put in all this heat shielding stuff. http://lh4.googleusercontent.com/-Xb...902_155436.jpg My friend cornholio also wrapped all post IC piping inside the engine bay.... in amazing carbon lava matt weave... this is lava mat and has the claimed ability to reflect heat up to 2k*. It look a bit ricer but is 100% functional. http://lh6.googleusercontent.com/-al...902_155610.jpg I also had my header and DP custom coated with a Super high temp coating that is suppose to help keep heat from radiating from the piping into my engine bay. Both my Exhaust Mani and my DP have the same coating. http://lh5.googleusercontent.com/-U1...902_155643.jpg 9krpmrx8 holding the fan pack. This set up pulls alot more air through the rad pac then the stock set up. The wiring on the fans is not larger then the OEM. It may draw a few more AMP's then normal but I am willing accept that. All connectors that have been cut or have redone to done to mil speck and hard soldered. http://lh6.googleusercontent.com/-WL...902_232245.jpg The last one for the night. So much work to do tomorrow. Not sure what to think but will drive on. I need to make the tuning date. http://lh4.googleusercontent.com/-Uh...902_233132.jpg |
That mani and engine mount bracket are not easy to install. You can see the coating on the manifold fairly well in this pic.
http://lh6.googleusercontent.com/--x...903_203039.jpg Up on chains! Check out the sexy carbonetic carbon clutch and flywheel set up. http://lh6.googleusercontent.com/-1S...903_203755.jpg It was not going in with both the engine bracket and kicked out oil pan. one had to be removed. http://lh6.googleusercontent.com/-ad...903_205555.jpg Where we stopped. We tried to a good 40 mins trying to get these bad boys mated up with no luck. http://lh4.googleusercontent.com/-vS...903_221508.jpg |
Only one picture from today but its a big one! Finally got the engine and tranny mated. Ended up having to pull them together with the bolts.
http://lh4.googleusercontent.com/-Fp...904_221224.jpg Both seats are in! http://lh5.googleusercontent.com/-AU...906_010938.jpg Here is Shadycrew AKA DC mother truckers working on the turbo http://lh4.googleusercontent.com/-kp...905_221649.jpg Here is the billet wheel. http://lh5.googleusercontent.com/-TW...905_221825.jpg 9krpmrx8 holding one of the housings for the turbo. We could not squeeze the turbo in place with it on. http://lh5.googleusercontent.com/-H0...905_222035.jpg this is what we did to protect the wheel while installing the turbo. http://lh3.googleusercontent.com/-op...905_223058.jpg Finally! http://lh6.googleusercontent.com/-7U...905_233855.jpg Here you can see some of the piping in place. http://lh5.googleusercontent.com/-Xw...906_010933.jpg Where I ended. Need to re-do the drain today somehow. http://lh6.googleusercontent.com/-Dd...906_005056.jpg |
http://lh6.googleusercontent.com/-p6...908_134550.jpg
All the turbo lines in place... other then the drain. http://lh6.googleusercontent.com/-IO...909_145402.jpg Here is the wiring going into place. What really dose not come out in these pictures is all the small stuff being done. Like the RB oil lines and rad pack set up. http://lh3.googleusercontent.com/-P9...909_191603.jpg Here you can see some of the methods I took to try and combat heat around the turbo. http://lh6.googleusercontent.com/-FG...911_203111.jpg Even my waste gate has its own exhaust! http://lh5.googleusercontent.com/-lB...911_213924.jpg |
Great... another one of those SARX guys is doing a build...
|
Is it mandatory to have a VR RX8 to be in SARX?
|
Originally Posted by Slidin8
(Post 4341244)
Is it mandatory to have a VR RX8 to be in SARX?
The build is looking good! It's awesome that you're getting good pictures of everything as you go. It's clear that all that time really helped you think about how to pull it all together. |
Thanks for the photo updates. Looks like a lot of thought has gone into the build great work!!
|
It's getting there , good job
|
Hey dude great pics your build is going rather quickly...
|
great pics buddy.
its my pleasure helping you out! even if its just doing the easy things.... have a really good time |
Looks good so far, What oil filter sandwich plate is that? Looks like the Golden Eagle one, I was looking at that one cause it would feed filtered oil to the turbo, but I wasn't sure if it would fit the 8.
|
Impressive stuff . I hope it measures up to your expectations .
This could be a SARX record for thread start time vs completion date :) |
So...I take it you guys like red cars? Loving the manifold man.
|
subbed ... gl with the build
|
Originally Posted by MongoRX
(Post 4341508)
So...I take it you guys like red cars? Loving the manifold man.
:cwm27: |
Good deal.... This is what I like to see... Good work guys...
|
Thread updated!
Originally Posted by Brettus
(Post 4341481)
Impressive stuff . I hope it measures up to your expectations .
This could be a SARX record for thread start time vs completion date :) |
Looks like you have a custom oil pan. Does it have a larger capacity than Greddy?
|
He's got the Rx8performance oil pan, it holds about 6 quarts.
Bad ass build BTW:bowdown: |
Originally Posted by skc
(Post 4341704)
Looks like you have a custom oil pan. Does it have a larger capacity than Greddy?
|
Looking good!
|
All times are GMT -5. The time now is 03:31 AM. |
© 2024 MH Sub I, LLC dba Internet Brands