Notices
RX-8 Discussion General discussion about the RX-8 that doesn't fit in one of the specialty forums.
Sponsored by:
Sponsored by: CARiD

New Proud RX8 owner

Old Aug 8, 2012 | 07:02 AM
  #1  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
New Proud RX8 owner

Hi ya folks,
New proud owner of a 2006 RX8 GT...Got it last friday...
From friday till today (wednesday) the love affair is still growing. I cant seem to grasp how much of a driver's car this machine is...A marvel of design and engineering, not to mention the built quality and material used. Simply blown away...This is M3 territory here invaded by the RX8..

The car have 85000 km and never seen winter...The interior is brand new so the outside. The folks at my local Mazda dealer painted the pront bumper cause of some minor scratches but nothing major.

The Mazda rep was kind enough to tell me about the regular maintenance of the engine. Not that i didnt researched it for 5 month though...

Got a bit sczred by reading the FAQ and the caring you need to do for this car to run properly. But afterwards it acurred to me that its not of a big a deal. I mean i dont mind as a enthousist to chek the oil after each fill up, change the entire ignition each 30k. Rev the engine from time to time to 9000 rpm (actually will be happy to)...

Yes it will cost a bit more in gaz cause of the 91 octane fuel and oil but who cares...couple of bucks more = load of driving heaven...

Coming from a mustang gt v8 torque i found it hard to get used to the 5000 rpm pickup of the 8...But after a day of driving i adjusted my driving technics and voila...

I mean im used to the gaz consumption cause my car that i traded in was A Mustang GT 2002...So they are are similar in gaz eating ability.

And to be on the safe side i purchased a bumper to bumper Warranty from mazda for 3 years or 60k more for $2500...The mazda sale person strongly suggested it and it was justified.

I still need to go back next monday for them to intall a brand new back right tail light. The one that always fills with water..My keyless entry is not working even with a new battery installed..A chek engine light and the famous red radiator dashboard light which i dought they can do anything about it...

Im having a bit of hesitation on first gear and a rough idle below 1000 rpm when the car gets hot. Is it cause she is due for an ignition system replacement at 85000 km?

All in all my only regret is wy i didnt dicover this car earlier on. lol...

Best of regards

Rabih

Reply
Old Aug 8, 2012 | 07:58 AM
  #2  
tcole6's Avatar
Registered
 
Joined: Apr 2010
Posts: 316
Likes: 0
From: NJ
If it hasn't been done in the last 30k, plugs, wires and coils. There are several DIYs posted for it if you are a do it yourselfer.

Congrats. You will continue to love it more and more. 2-1/2 years later, I'm still lovin it like the day I got it.
Reply
Old Aug 8, 2012 | 08:09 AM
  #3  
Hesselrode's Avatar
US Navy Rotary Enthusiast
iTrader: (3)
 
Joined: Aug 2007
Posts: 1,062
Likes: 3
From: New Orleans, LA
I agree with tcole. I bought mine in 2007 and still love it. Wash it weekly and take as much care of it as I can. It is a money pit and I have had every issue that you could have with it, but I don't care I still love it. There are preventative measures for almost all problems that occur in the 8, such as the clutch pedal reinforment. I would suggest that before your clutch pedal decides to snap one day when your driving 80 on the highway.
Reply
Old Aug 8, 2012 | 08:09 AM
  #4  
Art L's Avatar
Registered
 
Joined: Apr 2012
Posts: 30
Likes: 0
From: Kings Park, New York
Originally Posted by Rabih_rx8
...


I still need to go back next monday for them to intall a brand new back right tail light. The one that always fills with water..My keyless entry is not working even with a new battery installed..A chek engine light and the famous red radiator dashboard light which i dought they can do anything about it...

Im having a bit of hesitation on first gear and a rough idle below 1000 rpm when the car gets hot. Is it cause she is due for an ignition system replacement at 85000 km? ...



These are things that your bumper to bumper warranty should take care of.

The check engine light has to be scanned so you know what the problem is. Might have something to do with the hesitation. The radiator light most likely requires a new overflow bottle which has the float assembly inside. That's the usual culprit. When I bought my RX-8 a couple of months ago, it had the same issue. Make sure it gets fixed. The keyless entry they should also fix. I thought it was an un-needed bit of foo-foo, but after using it for a week, I was hooked. It a nice convenience.
Reply
Old Aug 8, 2012 | 08:14 AM
  #5  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
Originally Posted by tcole6
If it hasn't been done in the last 30k, plugs, wires and coils. There are several DIYs posted for it if you are a do it yourselfer.

Congrats. You will continue to love it more and more. 2-1/2 years later, I'm still lovin it like the day I got it.
Thanks man...I'm sure I'll love it that much as well...
Not sure if they changed the ignition system bit will do it myself anyways..it's fairly simple...I watched the do it yourself guide as well...
Driving to work 15 min ago it did hesitate on first gear...maybe I need to build up some rev before picking up...if I do launch the first gear at 2000 rpm there is no hesitAtion...but below that..oh lord put your neck restraints...
Reply
Old Aug 8, 2012 | 08:21 AM
  #6  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
Originally Posted by Hesselrode
I agree with tcole. I bought mine in 2007 and still love it. Wash it weekly and take as much care of it as I can. It is a money pit and I have had every issue that you could have with it, but I don't care I still love it. There are preventative measures for almost all problems that occur in the 8, such as the clutch pedal reinforment. I would suggest that before your clutch pedal decides to snap one day when your driving 80 on the highway.
Clutch cable snaps??? Dear lord r u serious??? If this happens you can be in gear or if ur lucky in neutral...
Is that a recall??? Covered by the extended warranty??? Or I need to go to my local mechanic and tel him weld here and weld there..
Reply
Old Aug 8, 2012 | 08:41 AM
  #7  
200.mph's Avatar
FULLY SEMI AUTOMATIC
iTrader: (9)
 
Joined: Aug 2008
Posts: 6,045
Likes: 3,484
From: BALLS DEEP
Originally Posted by Rabih_rx8
Clutch cable snaps??? Dear lord r u serious??? If this happens you can be in gear or if ur lucky in neutral...
Is that a recall??? Covered by the extended warranty??? Or I need to go to my local mechanic and tel him weld here and weld there..
8s dont have a clutch cable. its weak spot welds on the pedal assembly that break. mazda will replace it if it breaks but i dont think its an inproved design. there is a bracket for it aftermarket but i just unbolted the pedal and welded it. no more worries
Reply
Old Aug 8, 2012 | 08:47 AM
  #8  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
Originally Posted by 200.mph
8s dont have a clutch cable. its weak spot welds on the pedal assembly that break. mazda will replace it if it breaks but i dont think its an inproved design. there is a bracket for it aftermarket but i just unbolted the pedal and welded it. no more worries
Ah sorry I'm still the thinking in Mustang mod...true it's a hydrolic
Can u link me the after market part and if possible a link to a posse less thread on beer on how to weld and where if I decided to go with that...

Regards
Reply
Old Aug 8, 2012 | 08:55 AM
  #9  
200.mph's Avatar
FULLY SEMI AUTOMATIC
iTrader: (9)
 
Joined: Aug 2008
Posts: 6,045
Likes: 3,484
From: BALLS DEEP
iirc the bracket is from raceroots but seriously its much cheaper and less complicated to weld it. you can search for the thread because im lazy to look for it lol. pretty simple tho.i think there are two elec. connectors on the pedal assembly and i think three bolts. once its out you will see the crappy spot welds. the hardest part is crawling under the dash. if you dont have a welder take it to someone that does and they will see what needs to be welded
Reply
Old Aug 8, 2012 | 09:02 AM
  #10  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
Originally Posted by 200.mph
iirc the bracket is from raceroots but seriously its much cheaper and less complicated to weld it. you can search for the thread because im lazy to look for it lol. pretty simple tho.i think there are two elec. connectors on the pedal assembly and i think three bolts. once its out you will see the crappy spot welds. the hardest part is crawling under the dash. if you dont have a welder take it to someone that does and they will see what needs to be welded
Ah so this part is connected to the clutch pedal...I need to take it out I guess and go to a welder and out it back in myself...
Its ok man I'll search the forum for the fix...

Regards
Reply
Old Aug 8, 2012 | 09:03 AM
  #11  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
Originally Posted by Art L
These are things that your bumper to bumper warranty should take care of.

The check engine light has to be scanned so you know what the problem is. Might have something to do with the hesitation. The radiator light most likely requires a new overflow bottle which has the float assembly inside. That's the usual culprit. When I bought my RX-8 a couple of months ago, it had the same issue. Make sure it gets fixed. The keyless entry they should also fix. I thought it was an un-needed bit of foo-foo, but after using it for a week, I was hooked. It a nice convenience.
Ya all these problems are covered...wI'll be addressed on Monday...dropping of the 8 and picking up their rental...
Reply
Old Aug 8, 2012 | 09:04 AM
  #12  
200.mph's Avatar
FULLY SEMI AUTOMATIC
iTrader: (9)
 
Joined: Aug 2008
Posts: 6,045
Likes: 3,484
From: BALLS DEEP
yes the pedal is connected to a sheetmetal bracket. when you unbolt it from the firewall the entire clutch pedal assembly comes out. its pretty straight foward
Reply
Old Aug 8, 2012 | 09:11 AM
  #13  
JCrane82's Avatar
Trust Me, I'm an Engineer
iTrader: (3)
 
Joined: Apr 2011
Posts: 621
Likes: 7
From: Elkhorn, WI
Here is the Race Roots clutch reinforcement bracket:

Clutch Pedal Reinforcement Bracket

I am currently using it without issue for 9 months.
Reply
Old Aug 8, 2012 | 09:36 AM
  #14  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
Now if I can figure out how to post pics from my cell with this mobile version of the forum...
I want to show you toe beauty..
Reply
Old Aug 8, 2012 | 11:50 AM
  #15  
Polak Graphics's Avatar
Former Sponsor
 
Joined: Nov 2010
Posts: 751
Likes: 0
From: New Jersey
Welcome.

Upload them to the website or link them through photobucker
Reply
Old Aug 8, 2012 | 10:00 PM
  #16  
monchie's Avatar
I HATE SPEEDBUMPS!
 
Joined: Nov 2007
Posts: 8,549
Likes: 8
From: Las Vegas, NV
Welcome to the club.
Reply
Old Aug 8, 2012 | 10:30 PM
  #17  
Rabih_rx8's Avatar
Thread Starter
Registered User
 
Joined: Aug 2012
Posts: 8
Likes: 0
From: Montreal Canada
Glad to be here, thanks...

Here is some pics of Grape...yeah i call her Grape lol...

https://www.dropbox.com/s/dpbgb5zv6m...2019.42.48.jpg

https://www.dropbox.com/s/wc3qy4zc7d...2019.42.33.jpg

https://www.dropbox.com/s/1ce31ybvmd...%2019.42.02.jp
https://www.dropbox.com/s/jnfzkg4tlg...2019.42.57.jpg

https://www.dropbox.com/s/3ubanjljmn...2019.43.17.jpg
https://www.dropbox.com/s/xl9mo8io3c...2016.33.40.jpg
https://www.dropbox.com/s/b9r60h1ghh...2016.36.35.jpg
https://www.dropbox.com/s/1sdtg1uj9d...2016.37.17.jpg

Last edited by Rabih_rx8; Aug 9, 2012 at 06:38 AM.
Reply
Old Aug 9, 2012 | 07:37 AM
  #18  
Art L's Avatar
Registered
 
Joined: Apr 2012
Posts: 30
Likes: 0
From: Kings Park, New York
Nice color...good luck with it.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
mr. GrandGame
New Member Forum
6
Sep 9, 2025 10:41 PM
Skyl3r
New Member Forum
148
Dec 2, 2019 04:51 PM
akagc
RX-8's For Sale/Wanted
7
Aug 11, 2015 07:07 PM
Bamaham
New Member Forum
2
Jul 23, 2015 08:08 AM
RX7.9
New Member Forum
0
Jul 20, 2015 12:01 PM


Thread Tools
Rate This Thread
Rate This Thread:
You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -5. The time now is 05:05 PM.