Rx8 engine in seven
#1
Rx8 engine in seven
Hi all wankel / rotary heads
I joined this forum since i took on the adventure to build an seven with a 13B renesis engine in it.
I bought an UK car as Donor and have mounted the engine in the seven.
For the last hurdle to victory i will try to open a new thread about it.
Regards,
Walter
I joined this forum since i took on the adventure to build an seven with a 13B renesis engine in it.
I bought an UK car as Donor and have mounted the engine in the seven.
For the last hurdle to victory i will try to open a new thread about it.
Regards,
Walter
#2
FULLY SEMI AUTOMATIC
iTrader: (9)
you put a renny in an rx7? why? what gen 7?
#3
Ow sorry, i ment lotus super seven.
I simply call them seven's not realising that over here there are even more seven's .
My current symptom is that the Rx8 doesn't pull beyond 5500 rpm in third, and hesitates in lower gears to climb beyond.
- new D585 coils, wires, plugs;
- rebuild engine;
- UK 2004 231bhp, 6 port;
- OMP verified working (with forscan, you can see the actual position and the switch toggling on start-up;
- I only had room to place an K&N cone onto the MAF tube;
Suspecting:
- I reused an old fuel pump; perhaps to small, but the rev limit looks like a very nice limit...
- I coudn't use the DSC/ABS unit. So i need to make the messages myself.
Perhaps someone can give me the "valid" "known good" canbus messages for:
- Clutch switch, it isn't connected yet, but i didn't get the error yet
- Speed limit in the MCU?!?
- Is it possible that traction control is activated?and limiting power?? would be nice to get valid canbus messages for:
Id:
- 4C0
- 212 (dash status??
- 204
All above ID's are from DSC/ABS unit.
No DTC's present.
p.s. : I cant create a thread in Tech Series 1, wy?
I simply call them seven's not realising that over here there are even more seven's .
My current symptom is that the Rx8 doesn't pull beyond 5500 rpm in third, and hesitates in lower gears to climb beyond.
- new D585 coils, wires, plugs;
- rebuild engine;
- UK 2004 231bhp, 6 port;
- OMP verified working (with forscan, you can see the actual position and the switch toggling on start-up;
- I only had room to place an K&N cone onto the MAF tube;
Suspecting:
- I reused an old fuel pump; perhaps to small, but the rev limit looks like a very nice limit...
- I coudn't use the DSC/ABS unit. So i need to make the messages myself.
Perhaps someone can give me the "valid" "known good" canbus messages for:
- Clutch switch, it isn't connected yet, but i didn't get the error yet
- Speed limit in the MCU?!?
- Is it possible that traction control is activated?and limiting power?? would be nice to get valid canbus messages for:
Id:
- 4C0
- 212 (dash status??
- 204
All above ID's are from DSC/ABS unit.
No DTC's present.
p.s. : I cant create a thread in Tech Series 1, wy?
Last edited by Tkswdr; 06-06-2019 at 05:34 PM.
#4
FULLY SEMI AUTOMATIC
iTrader: (9)
theres a post count and wait time for new members before you can start threads. do you have a cat in the exhaust?
#6
Smoking turbo yay
What kind? I hope it's an HJS cat. Most cheap stuff won't last.
#8
Registered
Did you use the legit D585s? Or the Chinabay D585?
To check if its ignition. Either buy a HEI coil ignition tester to verify proper spark, or at very least, put a timing gun lead on both of your leading spark plug wires and make sure you are getting a nice steady flash.
To check if its ignition. Either buy a HEI coil ignition tester to verify proper spark, or at very least, put a timing gun lead on both of your leading spark plug wires and make sure you are getting a nice steady flash.
#9
Bought them on ebay, but they are from a brand i think they are aftermarket ones, but no china i hope.
They where send from the USA if that helps.
DTS part number: 08-UF-262
Can someone help me with the CAN messages?
Anyone have ing an china ELM which can make a scan?
Its easy todo!
They where send from the USA if that helps.
DTS part number: 08-UF-262
Can someone help me with the CAN messages?
Anyone have ing an china ELM which can make a scan?
Its easy todo!
Thread
Thread Starter
Forum
Replies
Last Post
DLrocket89
Series I Aftermarket Performance Modifications
11
02-08-2011 02:28 PM