Notices
New Member Forum A place for new members to get their feet wet

immobilizer issue sorted

Thread Tools
 
Rate Thread
 
Old Apr 16, 2016 | 06:41 AM
  #1  
bunnybonker's Avatar
Thread Starter
New Member
 
Joined: Apr 2016
Posts: 6
Likes: 0
immobilizer issue sorted

hi, ive a RX8 04 that had starting issues and found away of bypassing the immobilizer by attaching a wire to the positive battery terminal then an inline 15 amp fuse ( only because i had one ) push button switch to the solenoid on the starter, works a treat have to turn on ignition switch then push button, switch off as normal, as immobilizer only effects the operation of the starter,
Reply
Old Apr 16, 2016 | 08:49 AM
  #2  
Soldier's Avatar
Registered
 
Joined: Apr 2016
Posts: 88
Likes: 1
From: Australia
was this an aftermarket push starter instal?
Reply
Old Apr 16, 2016 | 09:17 AM
  #3  
bunnybonker's Avatar
Thread Starter
New Member
 
Joined: Apr 2016
Posts: 6
Likes: 0
yes bought from a motorfactors
Reply
Old Apr 16, 2016 | 10:12 AM
  #4  
bunnybonker's Avatar
Thread Starter
New Member
 
Joined: Apr 2016
Posts: 6
Likes: 0
IM about to do an engine swap, pulling a perfectly good running engine out a 04 231 and putting with fettling in a mazda mx5 1.6 with a gt4088v turbo with after de-tuning the turbo down to about 690 hp thru the stock 6 speed gearbox, should be good for 0-60 sub 2 sec, & 0-100 mph in 3,
Reply
Old Apr 16, 2016 | 03:31 PM
  #5  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,848
Likes: 1,804
From: Y-cat-o NZ
Originally Posted by bunnybonker
IM about to do an engine swap, pulling a perfectly good running engine out a 04 231 and putting with fettling in a mazda mx5 1.6 with a gt4088v turbo with after de-tuning the turbo down to about 690 hp thru the stock 6 speed gearbox, should be good for 0-60 sub 2 sec, & 0-100 mph in 3,
Wat ?
Reply
Old Apr 16, 2016 | 04:49 PM
  #6  
bunnybonker's Avatar
Thread Starter
New Member
 
Joined: Apr 2016
Posts: 6
Likes: 0
after the research already done it needs to be less than 700hp with out de-tunning it would make 980hp but the engine would last about 2 hours, for longevity sub 700hp it lasts with out damage im putting it through the 6 speed gear box of the 231 rx, the 1.6 has the bungs in the block for oil and water feeds for a turbo just need to modify the sump for oil return , also a carbon fibre crankshaft, titanium conrods, forged pistons, decompression plate, the turbo was destined for a 12.9 ltr bus engine as its a veritable vane turbo the smallest cc engine to spin it up is a 1.5 ltr as a 1.5 ltr engine @ 1100rpm is putting aprox the same pressure as the 12.9 @150 rpm, im in the building of the engine stage at the mo got to also build a test bed to get it all running sweet before cutting the firewall out of the rx,

yes im a total nutter i put a 4.2 yank into a suzuki sj410 just cos someone said "it wont work" ok so it wasn't 4 wheel drive and the end of the gearbox bolted straight onto the axle but it would out do anything else on the track,
Reply
Old Apr 16, 2016 | 05:23 PM
  #7  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,848
Likes: 1,804
From: Y-cat-o NZ
I still don't know what you are doing . What engine are you putting in what car ?
Reply
Old Apr 16, 2016 | 05:26 PM
  #8  
bunnybonker's Avatar
Thread Starter
New Member
 
Joined: Apr 2016
Posts: 6
Likes: 0
mx5 1.6 into a rx8 both mazda's
Reply
Old Apr 16, 2016 | 05:48 PM
  #9  
Brettus's Avatar
Boosted Kiwi
iTrader: (2)
 
Joined: Apr 2006
Posts: 20,848
Likes: 1,804
From: Y-cat-o NZ
so two engines.... both mx5 1.6L . One going into an mx5 and one into an 8 ? Did i guess that right ?
Reply
Old Apr 16, 2016 | 07:48 PM
  #10  
bunnybonker's Avatar
Thread Starter
New Member
 
Joined: Apr 2016
Posts: 6
Likes: 0
no it clearly says swap and also say taking out, the rx8 engine coming out and the mx5 engine going in
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
gsmith51234
New Member Forum
7
Jun 13, 2016 11:12 PM
garyross
New Member Forum
14
Apr 16, 2016 09:27 PM
Afrancis
New Member Forum
9
Apr 13, 2016 04:27 PM
RotaryMeister
New Member Forum
0
Apr 11, 2016 06:22 PM
CustomMSP
RX-8 Parts For Sale/Wanted
0
Apr 10, 2016 08:25 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -5. The time now is 03:24 PM.