code P2259 iddle at low rpm, not enough torque
11-03-2016, 07:22 AM
#1
New Member
Thread Starter
Join Date: Oct 2016
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
code P2259 iddle at low rpm, not enough torque
hello to everyone from greece.
im an owner of an rx8 year 2005 192hp. The last 9 months i have change the coils,spark plugs,both O2 sensors,fuel pump,maf sensor,the ECU unit and all these because of a problem in my two primary injection system.
Last week i changed the 2 injectors and appears the CEL with code P2259.
I change the blue and white solenoids under the intake but the problem is still there.
The symptoms are,iddle at low rpm and i feel that i have no torque especially after 3500 rpm.Its going from 1000 rpm to 7000 rpm smoothly,and a little bit of catback missfire.
My engine compression its very good as i have rebuild it 30.000 km earlier.
I dont know what else to do so i can finally drift again..!!!
i have 125.000 km right now.
Thank you for your time everyone and im very sorry for my english.I hope you will understand what im writing...
im an owner of an rx8 year 2005 192hp. The last 9 months i have change the coils,spark plugs,both O2 sensors,fuel pump,maf sensor,the ECU unit and all these because of a problem in my two primary injection system.
Last week i changed the 2 injectors and appears the CEL with code P2259.
I change the blue and white solenoids under the intake but the problem is still there.
The symptoms are,iddle at low rpm and i feel that i have no torque especially after 3500 rpm.Its going from 1000 rpm to 7000 rpm smoothly,and a little bit of catback missfire.
My engine compression its very good as i have rebuild it 30.000 km earlier.
I dont know what else to do so i can finally drift again..!!!
i have 125.000 km right now.
Thank you for your time everyone and im very sorry for my english.I hope you will understand what im writing...
Last edited by vasilispyr7; 11-03-2016 at 07:36 AM.
11-03-2016, 01:28 PM
#3
New Member
Thread Starter
Join Date: Oct 2016
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
yes... i changed the top and the middle one.
as i was driving today,the CEL started blinking and the engine stalled(like i switch off the key.) for 6-7 seconds
Last edited by vasilispyr7; 11-03-2016 at 01:35 PM.
11-04-2016, 11:58 AM
#5
New Member
Thread Starter
Join Date: Oct 2016
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Ok... I think im gonna be crazy with the car..!!!! Today,and after i left home,after 5 minutes the CEL start blinking again and the car stalled... I pull over and i tried to turn on the engine.. Nothing... I was waiting for 10 minutes and the engine finally statred. Now i have P0301 code ( first rotor misfire) with the same symptoms..!! Iddle at low rpm and no torque.... Please help.
11-06-2016, 01:58 PM
#6
New Member
Join Date: Oct 2016
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Ok... I think im gonna be crazy with the car..!!!! Today,and after i left home,after 5 minutes the CEL start blinking again and the car stalled... I pull over and i tried to turn on the engine.. Nothing... I was waiting for 10 minutes and the engine finally statred. Now i have P0301 code ( first rotor misfire) with the same symptoms..!! Iddle at low rpm and no torque.... Please help.
hotstart issue, its common. i usually have to wait 5-10min, rotary life bro.
11-24-2016, 03:17 PM
#8
New Member
Join Date: Nov 2016
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Air
Ssv
Udi