RX8Club.com

RX8Club.com (https://www.rx8club.com/)
-   New Member Forum (https://www.rx8club.com/new-member-forum-197/)
-   -   code P2259 iddle at low rpm, not enough torque (https://www.rx8club.com/new-member-forum-197/code-p2259-iddle-low-rpm-not-enough-torque-263806/)

vasilispyr7 11-03-2016 07:22 AM

code P2259 iddle at low rpm, not enough torque
 
hello to everyone from greece.
im an owner of an rx8 year 2005 192hp. The last 9 months i have change the coils,spark plugs,both O2 sensors,fuel pump,maf sensor,the ECU unit and all these because of a problem in my two primary injection system.
Last week i changed the 2 injectors and appears the CEL with code P2259.
I change the blue and white solenoids under the intake but the problem is still there.
The symptoms are,iddle at low rpm and i feel that i have no torque especially after 3500 rpm.Its going from 1000 rpm to 7000 rpm smoothly,and a little bit of catback missfire.
My engine compression its very good as i have rebuild it 30.000 km earlier.
I dont know what else to do so i can finally drift again..!!!
i have 125.000 km right now.

Thank you for your time everyone and im very sorry for my english.I hope you will understand what im writing...

wcs 11-03-2016 07:44 AM

P2259 =AIR solenoid valve control circuit low

I can't recall the colour of those solenoids but I believe the Air Solenoid is the top one.
Is that one of the solenoids you had replaced?

vasilispyr7 11-03-2016 01:28 PM


Originally Posted by wcs (Post 4789698)
P2259 =AIR solenoid valve control circuit low

I can't recall the colour of those solenoids but I believe the Air Solenoid is the top one.
Is that one of the solenoids you had replaced?


yes... i changed the top and the middle one.

as i was driving today,the CEL started blinking and the engine stalled(like i switch off the key.) for 6-7 seconds

iRedline 11-03-2016 01:35 PM

torque?
 
whats that?:nono:

vasilispyr7 11-04-2016 11:58 AM

Ok... I think im gonna be crazy with the car..!!!! Today,and after i left home,after 5 minutes the CEL start blinking again and the car stalled... I pull over and i tried to turn on the engine.. Nothing... I was waiting for 10 minutes and the engine finally statred. Now i have P0301 code ( first rotor misfire) with the same symptoms..!! Iddle at low rpm and no torque.... Please help.

iRedline 11-06-2016 01:58 PM


Originally Posted by vasilispyr7 (Post 4790046)
Ok... I think im gonna be crazy with the car..!!!! Today,and after i left home,after 5 minutes the CEL start blinking again and the car stalled... I pull over and i tried to turn on the engine.. Nothing... I was waiting for 10 minutes and the engine finally statred. Now i have P0301 code ( first rotor misfire) with the same symptoms..!! Iddle at low rpm and no torque.... Please help.



hotstart issue, its common. i usually have to wait 5-10min, rotary life bro.:nono:

wcs 11-06-2016 07:35 PM

Hot start is no common lol well it shouldn't be.
Hot start = low compression

Flashing (blinking check engine light) is a misfire (your p0301 code)

If you're not a mechanic ... well that sucks because you have some work to do.

Optimus Prime 11-24-2016 03:17 PM


Originally Posted by vasilispyr7 (Post 4789823)
yes... i changed the top and the middle one.

as i was driving today,the CEL started blinking and the engine stalled(like i switch off the key.) for 6-7 seconds

Hey I need to replace the three solenoid valve having a hard time where to get them anyone knows please a little help thank you
Air
Ssv
Udi


All times are GMT -5. The time now is 06:39 AM.


© 2024 MH Sub I, LLC dba Internet Brands