Official Mod Day Thread For SARX
#31
thats kewl... but if you are coming that early you better bring some breakfast tacos too
I still have some of the gatorade and water that was left over from the last meet, bring anything else you want.... <cough> beer <cough>
I still have some of the gatorade and water that was left over from the last meet, bring anything else you want.... <cough> beer <cough>
#33
SARX Legend
Thread Starter
iTrader: (46)
I will bet there Saturday but unfortunately due to problems locating **** I probably won't do anything. It's very frustrating. Still no shocks, still need another pair of spacers, and still no rims. The cooler stuff is getting complicated too but I should have all the fittings, hose brackets, etc. by the end of this weekend. The local places I have contacted all only have bits an pieces so my dad had to round of all the stuff for me.
#35
SARX Legend
Thread Starter
iTrader: (46)
I may take you up on that. I'm thinking of taking a day off during the week to do the battery relocation and the SOHN because I need to get it done. The shocks will be an all day affair (when I get them) and then I need help installing the oil pressure gauge.
The cooler will need an all day Saturday because I wanna do it right. The rear rotors and pads could definitely be an after work job. What else, HMMMM.....
The cooler will need an all day Saturday because I wanna do it right. The rear rotors and pads could definitely be an after work job. What else, HMMMM.....
#36
SARX
iTrader: (2)
I may take you up on that. I'm thinking of taking a day off during the week to do the battery relocation and the SOHN because I need to get it done. The shocks will be an all day affair (when I get them) and then I need help installing the oil pressure gauge.
The cooler will need an all day Saturday because I wanna do it right. The rear rotors and pads could definitely be an after work job. What else, HMMMM.....
The cooler will need an all day Saturday because I wanna do it right. The rear rotors and pads could definitely be an after work job. What else, HMMMM.....
Jay how about putting on those Grille Guys screen's ????
I was gonna clay bar/wax my car...
Last edited by cornholio135; 11-04-2009 at 10:02 PM.
#46
Lucky #33
iTrader: (4)
To easy! You can use plastic from about anywhere! If i were to put an inlet in the bottom of the under tray I would simply cut the under tray and and Use JB Weld or something smiler to it to bond some plastic sourced from a bit of scrap.
Cut a l___l shape into the under tray make a few triangle shaped plastic cut outs and JB weld them into the open space on the side of the flange you just pushed down.
Cut a l___l shape into the under tray make a few triangle shaped plastic cut outs and JB weld them into the open space on the side of the flange you just pushed down.
#48
SARX
iTrader: (2)
To easy! You can use plastic from about anywhere! If i were to put an inlet in the bottom of the under tray I would simply cut the under tray and and Use JB Weld or something smiler to it to bond some plastic sourced from a bit of scrap.
Cut a l___l shape into the under tray make a few triangle shaped plastic cut outs and JB weld them into the open space on the side of the flange you just pushed down.
Cut a l___l shape into the under tray make a few triangle shaped plastic cut outs and JB weld them into the open space on the side of the flange you just pushed down.
on ebay they are cheap
http://cgi.ebay.com/ebaymotors/SUBAR...Q5fAccessories
#49
SARX Legend
Thread Starter
iTrader: (46)
Hey you may be on to something... Mounted upside down. I wonder how wide it is?
hey Corn, you know if a good place to get 2 gauge wire and two fuse blocks?
hey Corn, you know if a good place to get 2 gauge wire and two fuse blocks?
Last edited by 9krpmrx8; 11-06-2009 at 01:22 PM.