Dallas Install Party??
#77
Registered
iTrader: (1)
Join Date: Oct 2007
Location: Fort Worth, Texas
Posts: 1,691
Likes: 0
Received 0 Likes
on
0 Posts
Ok, Should be there around 2:30
I just got off the phone with the Rx8club rep over at tirerack.com
My hawk ceramic HPS should be in on friday for 105 (75 for the front set and the rest for overnight shipping) Wish I would have gotten an answer sooner from Hiley, cuse that could have saved me a few more bucks on shipping
I should be going into the dealer sometime tom morning to get the two new front kumo's on for 117 a pop plus 15 install for each tire.
So hopefully we can do my pads On sunday and I can be free from sqeeky breaks.
I just got off the phone with the Rx8club rep over at tirerack.com
My hawk ceramic HPS should be in on friday for 105 (75 for the front set and the rest for overnight shipping) Wish I would have gotten an answer sooner from Hiley, cuse that could have saved me a few more bucks on shipping
I should be going into the dealer sometime tom morning to get the two new front kumo's on for 117 a pop plus 15 install for each tire.
So hopefully we can do my pads On sunday and I can be free from sqeeky breaks.
#83
Registered
iTrader: (1)
Join Date: Oct 2007
Location: Fort Worth, Texas
Posts: 1,691
Likes: 0
Received 0 Likes
on
0 Posts
Just a list of stuff I need to bring besides the PADS (i know we talked about rotors but the lady it was pads even though I swear the paperwork says rotors)
Anyway, angie said something about c-clamp? And I think you mentioned something about brake grease as well, just wanted to know what it is exactly I need and if there is anything else I need to pick up?
Anyway, angie said something about c-clamp? And I think you mentioned something about brake grease as well, just wanted to know what it is exactly I need and if there is anything else I need to pick up?
#85
It's good to be the king.
Join Date: Jan 2006
Location: Corinth, TX
Posts: 1,406
Likes: 0
Received 0 Likes
on
0 Posts
Riley, if you're doing all 4, you'll need a C clamp for one set and a brake caliper tool for the other. You can "rent" one from AutoZone. Just give them a deposit on it and bring it back within 90 days and you get your money back.
#88
www.thetexas8.com
iTrader: (3)
Join Date: Jan 2008
Location: Mars Bitches
Posts: 913
Likes: 0
Received 0 Likes
on
0 Posts
So far from what I remember we have these things to do Sunday:
Travis- Springs
Thomas (taker of lamb virginity)- haha- Has brake pads needing to be installed.
Scott- Brake lines and clutch lines?
Nick: plugs, wires, and RP supercat
What else?
Travis- Springs
Thomas (taker of lamb virginity)- haha- Has brake pads needing to be installed.
Scott- Brake lines and clutch lines?
Nick: plugs, wires, and RP supercat
What else?
Last edited by seatownracer; 06-19-2008 at 10:44 AM.
#91
Registered
iTrader: (1)
Join Date: Oct 2007
Location: Fort Worth, Texas
Posts: 1,691
Likes: 0
Received 0 Likes
on
0 Posts
I am only going to do the front pads, which tool do I need for the front? Is the C clamp a special tool or just one of those things you use to hold wood in place while you cut it?
#93
Registered
Join Date: Feb 2007
Location: Richardson, TX
Posts: 838
Likes: 0
Received 0 Likes
on
0 Posts
I have a C clamp, give me a call if you forget to run by Auto Zone and I'll bring it by. Or you can stop by and get it on your way to the install party...either way.
#94
Iraqi Freedom Veteran x2
Join Date: Sep 2005
Location: at work probably
Posts: 230
Likes: 0
Received 0 Likes
on
0 Posts
hey its been a while since i've been on... somebody pm me with the directions and i'll try and show up and give a hand... just one.... beer for the other....
#95
Dragon Certified
Thread Starter
iTrader: (1)
Join Date: Dec 2005
Location: Roanoke Tx
Posts: 829
Likes: 0
Received 0 Likes
on
0 Posts
Just a list of stuff I need to bring besides the PADS (i know we talked about rotors but the lady it was pads even though I swear the paperwork says rotors)
Anyway, angie said something about c-clamp? And I think you mentioned something about brake grease as well, just wanted to know what it is exactly I need and if there is anything else I need to pick up?
Anyway, angie said something about c-clamp? And I think you mentioned something about brake grease as well, just wanted to know what it is exactly I need and if there is anything else I need to pick up?
#96
It's good to be the king.
Join Date: Jan 2006
Location: Corinth, TX
Posts: 1,406
Likes: 0
Received 0 Likes
on
0 Posts
Just to make sure there isn't confusion on this point. While AutoZone does carry C clamps, they are not available for "rent". It's the special service tool that they have for rent.
#97
Turbo SR20deT Son!
Join Date: Jun 2007
Location: North. dallas(Texas)
Posts: 790
Likes: 0
Received 0 Likes
on
0 Posts
#98
Nick
#99
Master Shr3dd3r
Join Date: May 2008
Location: Colleyville, TX
Posts: 217
Likes: 0
Received 0 Likes
on
0 Posts
So I would like to get my Rotary Rasp footwells installed with a switch in those open switch slots but I'm not really sure what I need to bring Sunday to make that happen. I can run to the store and get a switch for it, but I dont know how or what kind of wiring to use and how to even run it to make that work. Anybody think they can help me out??