Offical New Rx8 LED Brake Light Group Buy
#51
fō'tə-jěn'
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Temple City, CA
Posts: 379
Likes: 0
Received 0 Likes
on
0 Posts
sorry for the delay, i will get the rest of the payment today and ship out with tracking number as well. i will send out PM with tracking conformation once it is available.
#55
The RX-8 is missed
iTrader: (3)
Join Date: Aug 2005
Location: Houston, TX
Posts: 2,084
Likes: 0
Received 0 Likes
on
0 Posts
will you pm back to confirm? just want to make sure my payment and pm went through ok...
EDIT: sorry, just saw "PAID" was by my name...i'm an idiot. thanks!
EDIT: sorry, just saw "PAID" was by my name...i'm an idiot. thanks!
Last edited by 2tone; 12-15-2008 at 04:00 PM.
#63
Registered
iTrader: (1)
Join Date: May 2008
Location: EP, TX
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
If you do have LED tail/brake lights as well, what kind of load resistor would you use? And would you put in with the third brake light or with the tail/brake lights or all?
Would any of the 6 ohm ones on ebay do fine?
Would any of the 6 ohm ones on ebay do fine?
#66
My 8 looks like a Smurf
iTrader: (4)
Join Date: Sep 2007
Location: Ottawa, ON, Canada
Posts: 1,742
Likes: 0
Received 0 Likes
on
0 Posts
The resistors should be about 10 ohms, 25W each. Don't buy them, you can make them for pennies... just go over to any electrical supply store and pick up the resistors (like $0.05 each), some shrink wrap ($0.50/yard -- you'll need about an inch per resistor) and some connectors or wire taps (maybe $0.25). These things are so over priced it makes me want to start selling some
Last edited by TheWulf; 12-16-2008 at 08:11 AM.
#68
fō'tə-jěn'
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Temple City, CA
Posts: 379
Likes: 0
Received 0 Likes
on
0 Posts
Both payment have been received and will be shipped out today, tracking number will be available tmr. Thanks
Thanks for the explanation. All tracking number and confirmation number already been send out, PM me if anyone did not received the numbers. Thanks
I just asked this question to Rotary Rasp -- which is our resident LED expert. You need one resistor per turn signal (wired in series) if you have LED turn signals, you do not need any for brake lights.
The resistors should be about 10 ohms, 25W each. Don't buy them, you can make them for pennies... just go over to any electrical supply store and pick up the resistors (like $0.05 each), some shrink wrap ($0.50/yard -- you'll need about an inch per resistor) and some connectors or wire taps (maybe $0.25). These things are so over priced it makes me want to start selling some
The resistors should be about 10 ohms, 25W each. Don't buy them, you can make them for pennies... just go over to any electrical supply store and pick up the resistors (like $0.05 each), some shrink wrap ($0.50/yard -- you'll need about an inch per resistor) and some connectors or wire taps (maybe $0.25). These things are so over priced it makes me want to start selling some
#70
Registered Toker
iTrader: (2)
OK I got my light in the mail today... looks good upon opening. The light itself IS back pretty far into the housing (will have to wait how it looks once installed). Smoked is not really smoked that much, so I will try to darken up the tint when I get home. Other than that, looks like good build quality and housing. I won't be able to install it until Jan. when I get home but hopefully someone else will upload pics when recieved.
#72
My 8 looks like a Smurf
iTrader: (4)
Join Date: Sep 2007
Location: Ottawa, ON, Canada
Posts: 1,742
Likes: 0
Received 0 Likes
on
0 Posts
I hope mine gets here within the next week... my 8 is parked for the winter at my mom's and I get to check up on her over xmas
Knowing customs I'll get it by Valentine's day
Knowing customs I'll get it by Valentine's day
#75
I got mine too, same one as Ross.
I did not get to install it, probably tomorrow. I will take pics. The smoked is not that dark, but it looks good still. Easily fixed if wanted. And yes the light is far back into the housing, but the oem one is about the same. Can't wait to install it. Thanks saki for setting this up. Fast delivery.
I did not get to install it, probably tomorrow. I will take pics. The smoked is not that dark, but it looks good still. Easily fixed if wanted. And yes the light is far back into the housing, but the oem one is about the same. Can't wait to install it. Thanks saki for setting this up. Fast delivery.