GB: One Touch Close Sunroof Module
#77
Administrator
iTrader: (7)
they work every time.
#79
Administrator
iTrader: (7)
^^^ and were any limbs injured during the installation of this mod?
#80
I zoom therefore I am.
It was a bloodless install. I can take that console out in my sleep, just printed out the one picture that shows tapping the red wire and connecting to the point of the blue wire.
It's very nice to just push the button once, pull the e brake, grab my phone and shut off the car.
It's very nice to just push the button once, pull the e brake, grab my phone and shut off the car.
#81
Registered
iTrader: (2)
Very nice, I purchased the DEI 530T so that I can make the windows one touch and controlled with the alarm.
So when I install this sunroof mod, can it take a trigger from an alarm to close it?
Making it a true one touch for the car by locking and all the windows and sunroof close. Or open in the summer to let the hot air out.
So when I install this sunroof mod, can it take a trigger from an alarm to close it?
Making it a true one touch for the car by locking and all the windows and sunroof close. Or open in the summer to let the hot air out.
#82
Drive it like u stole it!
iTrader: (2)
Join Date: Nov 2007
Location: mobile, al
Posts: 1,050
Likes: 0
Received 0 Likes
on
0 Posts
Very nice, I purchased the DEI 530T so that I can make the windows one touch and controlled with the alarm.
So when I install this sunroof mod, can it take a trigger from an alarm to close it?
Making it a true one touch for the car by locking and all the windows and sunroof close. Or open in the summer to let the hot air out.
So when I install this sunroof mod, can it take a trigger from an alarm to close it?
Making it a true one touch for the car by locking and all the windows and sunroof close. Or open in the summer to let the hot air out.
#84
Registered
iTrader: (2)
https://www.rx8club.com/showthread.p...ht=diy+sunroof
Kudos to vrpirata.
#86
503wtq Boosted Bimmer
Thread Starter
iTrader: (2)
Join Date: Oct 2004
Location: Los Angeles, California
Posts: 3,038
Likes: 0
Received 0 Likes
on
0 Posts
It was a bloodless install. I can take that console out in my sleep, just printed out the one picture that shows tapping the red wire and connecting to the point of the blue wire.
It's very nice to just push the button once, pull the e brake, grab my phone and shut off the car.
It's very nice to just push the button once, pull the e brake, grab my phone and shut off the car.
#88
Registered
iTrader: (6)
Join Date: Jun 2007
Location: Pleasanton, CA
Posts: 1,781
Likes: 0
Received 0 Likes
on
0 Posts
4 Years... Can you make a DIY thread when you finish this? Thanks.
Rotary Rasp... This GB for the sundroof module isn't ending soon is it? If so, I need to buy one. Otherwise I am probably going to wait a little longer before buying it.
Rotary Rasp... This GB for the sundroof module isn't ending soon is it? If so, I need to buy one. Otherwise I am probably going to wait a little longer before buying it.
#89
resist, un-learn, defy...
Join Date: Oct 2007
Location: ewa beach, hawaii
Posts: 243
Likes: 0
Received 0 Likes
on
0 Posts
i still haven't figured out the powered sunroof DIY. i'm scared to cut the wrong P/B wire. how do you find out which one? i can't tell from looking at the pics and diagrams....
#93
Registered
iTrader: (2)
The Green / yellow is the one in the opposite corner of the clip as the correct pink / black. I clipped the tape that had it held together, makes it much easier.
I didn't check to see what the other pink / black wire is for.
#94
Registered
iTrader: (2)
I will if needed but I think Rotary Rasp did a good job in the first post showing where the connections are for this one touch module.
The one thing he may have missed is where to press the clips on the map light assembly to release next to the lights.
I did it last night to hard wire my Valentine One. It is about an inch in from the back of the car on the sides of the map light assembly.
Go in a little bit horizontally with the screwdriver and then move the screwdriver tip toward the ceiling about a fourth of an inch. Then push the clip in toward the map light assembly while pulling down on the back of the assembly. Do one corner and then you should be able to shimmy the other corner out.
I think there may be directions in the manual as well but I don't remember them being as helpful... if you can make heads or tails of my long winded descriptive description.
There is a DIY on how to remove the map light assembly.
https://www.rx8club.com/series-i-do-yourself-forum-73/diy-correct-way-remove-maplight-sunroof-switch-unit-97596/
#95
Registered
iTrader: (6)
Join Date: Jun 2007
Location: Pleasanton, CA
Posts: 1,781
Likes: 0
Received 0 Likes
on
0 Posts
I will if needed but I think Rotary Rasp did a good job in the first post showing where the connections are for this one touch module.
The one thing he may have missed is where to press the clips on the map light assembly to release next to the lights.
I did it last night to hard wire my Valentine One. It is about an inch in from the back of the car on the sides of the map light assembly.
Go in a little bit horizontally with the screwdriver and then move the screwdriver tip toward the ceiling about a fourth of an inch. Then push the clip in toward the map light assembly while pulling down on the back of the assembly. Do one corner and then you should be able to shimmy the other corner out.
I think there may be directions in the manual as well but I don't remember them being as helpful... if you can make heads or tails of my long winded descriptive description.
There is a DIY on how to remove the map light assembly.
https://www.rx8club.com/showthread.php?t=97596
The one thing he may have missed is where to press the clips on the map light assembly to release next to the lights.
I did it last night to hard wire my Valentine One. It is about an inch in from the back of the car on the sides of the map light assembly.
Go in a little bit horizontally with the screwdriver and then move the screwdriver tip toward the ceiling about a fourth of an inch. Then push the clip in toward the map light assembly while pulling down on the back of the assembly. Do one corner and then you should be able to shimmy the other corner out.
I think there may be directions in the manual as well but I don't remember them being as helpful... if you can make heads or tails of my long winded descriptive description.
There is a DIY on how to remove the map light assembly.
https://www.rx8club.com/showthread.php?t=97596