RX8Club.com
Bluetooth Electronics interface to my Arduino Nano Every w/BLE module. I have the delaySCoff currently set to 4000ms, this keeps the SC clutch engaged for 4 second after the throttle drops below 30% so I can shift gears without the clutch having to reengage, no boost lag between gear shifts! The delayWMon waits to turn on the WM pump, 400ms currently. There are a lot more setting in the software that I added but these are the ones I'm focusing on now.
Bluetooth Electronics interface to my Arduino Nano Every w/BLE module. I have the delaySCoff currently set to 4000ms, this keeps the SC clutch engaged for 4 second after the throttle drops below 30% so I can shift gears without the clutch having to reengage, no boost lag between gear shifts! The delayWMon waits to turn on the WM pump, 400ms currently. There are a lot more setting in the software that I added but these are the ones I'm focusing on now.
0 2020/06/09 22:01:09
The bracket and pump ready and the wiring and WM line connected and tucked away. I ran the wiring and WM line out a grommet in the trunk and under the car on the fuel line rack up to the engine bay.
The bracket and pump ready and the wiring and WM line connected and tucked away. I ran the wiring and WM line out a grommet in the trunk and under the car on the fuel line rack up to the engine bay.
0 2020/05/15 22:39:19
Ran the WM line and wires from the trunk, under the car and hung them on the fuel line rails all the way up to the engine bay. Now the fun part!
Ran the WM line and wires from the trunk, under the car and hung them on the fuel line rails all the way up to the engine bay. Now the fun part!
0 2020/05/15 22:39:31
0 2020/05/02 08:26:11
0 2020/05/02 08:25:58
inject W/M here?
inject W/M here?
0 2020/05/01 22:40:15
0 2020/04/30 22:25:21
0 2020/04/30 22:24:47
0 2020/04/30 21:40:36
Ready to go!
Ready to go!
0 2020/04/19 17:02:58
...more rebuilding
...more rebuilding
0 2020/04/19 17:02:48
it's really a Ogura TX12 compressor...
it's really a Ogura TX12 compressor...
0 2020/04/19 17:02:40
...just something fun, found these door emblem projectors on ebay and installed in both doors
...just something fun, found these door emblem projectors on ebay and installed in both doors
0 2020/04/19 17:02:22
May fresh rebuild, June of 2017
May fresh rebuild, June of 2017
0 2020/04/19 17:02:12
0 2020/04/19 16:58:39
0 2020/04/19 16:58:30
Ready to go!
Ready to go!
0 2020/04/19 16:58:08
Rebuilding the supercharger
Rebuilding the supercharger
0 2020/04/19 16:57:59
My fresh rebuild, June of 2017
My fresh rebuild, June of 2017
0 2020/04/19 16:57:07
...details
...details
0 2020/04/19 10:17:08
the devil is in the...
the devil is in the...
0 2020/04/19 10:16:38
...in with the new!
...in with the new!
0 2020/04/19 10:12:10
Out with the old..
Out with the old..
0 2020/04/19 10:11:34
98N is the pressure you need to put on the belt and 2.0 - 2.8mm is the short belt deflection and 2.3 - 3.0mm is the long belt deflection
98N is the pressure you need to put on the belt and 2.0 - 2.8mm is the short belt deflection and 2.3 - 3.0mm is the long belt deflection
0 2020/06/18 13:35:02
...but worth it in the end.
...but worth it in the end.
0 2020/04/19 10:11:01
What a pain!
What a pain!
0 2020/04/19 10:10:28
0 2020/08/17 23:58:04
0 2020/08/20 00:01:06
Making my own wiring harness.
Making my own wiring harness.
0 2020/04/19 10:09:40
0 2020/08/20 00:03:39
Full kit from Blitz. Cost $8k or $9k new back in '04.
Full kit from Blitz. Cost $8k or $9k new back in '04.
0 2020/04/19 09:35:38
Kit I bought off ebay for $1600 shipped directly from Japan. Took 2 months to get here.
Kit I bought off ebay for $1600 shipped directly from Japan. Took 2 months to get here.
0 2020/04/19 09:33:40
0 2020/08/20 00:07:00
Greedy map the turns on the compressor at ~30%
Greedy map the turns on the compressor at ~30%
0 2020/04/19 09:31:51
Chip's resurfaced and renitrided my side housings.
Chip's resurfaced and renitrided my side housings.
0 2020/08/25 09:24:04
Boost controller, AFR gauge and the SC on-demand buttons.
Boost controller, AFR gauge and the SC on-demand buttons.
0 2020/04/18 18:27:47
...and some new rotor housings
...and some new rotor housings
0 2020/08/25 09:24:17
...and all new OE seals from a Racing Beat kit I picked up on EBay for $900.
...and all new OE seals from a Racing Beat kit I picked up on EBay for $900.
0 2020/08/25 09:25:44
Shot of the air tank, solenoid, keg regulator and the arduino.
Shot of the air tank, solenoid, keg regulator and the arduino.
0 2020/04/18 18:25:42
Dropping in the fresh rebuild. The trans got a rebuild too and went in the day before
Dropping in the fresh rebuild. The trans got a rebuild too and went in the day before
0 2020/09/14 20:47:57