RX8Club.com
fan shroud fits too
fan shroud fits too
0 2021/08/25 13:52:56
looked at my spare trans. dunno how i never noticed this, but the shifter has a kick to the side.
looked at my spare trans. dunno how i never noticed this, but the shifter has a kick to the side.
0 2021/09/26 11:58:02
The rx8 column didn't quite fit, but a couple new holes in the dash support fixed that up.
The rx8 column didn't quite fit, but a couple new holes in the dash support fixed that up.
0 2021/09/04 15:45:23
a sorry state of affairs for the NC
a sorry state of affairs for the NC
0 2022/06/14 20:34:37
0 2021/08/15 18:19:02
0 2021/08/20 21:11:37
Both have grommets with this nasty rubber cement filling them up. cutting it away is a pain
Both have grommets with this nasty rubber cement filling them up. cutting it away is a pain
0 2021/08/20 21:11:35
i don't even know what to say about this
i don't even know what to say about this
0 2022/08/22 05:48:09
0 2021/11/08 07:27:50
Exhaust is kinda close to the side of the tunnel here. it's not touching anything currently, but it's pretty close and i don't really want it catching on fire. I'll likely bash the sides in a little bit for got luck.
Exhaust is kinda close to the side of the tunnel here. it's not touching anything currently, but it's pretty close and i don't really want it catching on fire. I'll likely bash the sides in a little bit for got luck.
0 2021/09/25 13:19:59
running the rx8 ECU in the stock NC location
running the rx8 ECU in the stock NC location
0 2021/10/04 19:23:15
0 2022/08/28 21:15:11
stripped clean
stripped clean
0 2022/08/28 21:15:27
engine out
engine out
0 2022/08/28 21:15:18
harness about to come out
harness about to come out
0 2022/09/02 20:53:40
this shows the spacer required to fit the NC ppf to the rx8 diff
this shows the spacer required to fit the NC ppf to the rx8 diff
0 2021/09/13 17:21:42
0 2021/08/20 21:11:39
chassis and engine harness separated
chassis and engine harness separated
0 2022/08/08 20:36:02
(mostly) stripped down of tape on the NC harness
(mostly) stripped down of tape on the NC harness
0 2021/08/20 21:11:34
harvested NC harness
harvested NC harness
0 2022/09/02 20:53:43
0 2022/08/28 21:15:18
0 2022/08/28 21:15:20
mostly finished peeling all the rubber cement off the individual wires, so that i can start stripping things out of the harness
mostly finished peeling all the rubber cement off the individual wires, so that i can start stripping things out of the harness
0 2021/08/20 21:11:33
here's an angle of it inside the miata
here's an angle of it inside the miata
0 2021/09/26 11:58:02
going to need to fabricate a bracket to mount the air pump over here
going to need to fabricate a bracket to mount the air pump over here
0 2021/10/04 19:23:13
loaded all the components into the engine bay to pretend it's done
loaded all the components into the engine bay to pretend it's done
0 2021/10/04 19:23:14
Found a spot for the electric power steering module. will need a bracket of course.
Found a spot for the electric power steering module. will need a bracket of course.
0 2021/10/18 07:04:43
nasty rubber cement goop on the grommets. this took a long time to clean up
nasty rubber cement goop on the grommets. this took a long time to clean up
0 2021/08/25 13:52:56
making a bench-x8
making a bench-x8
0 2022/08/28 21:15:27
0 2021/11/08 07:27:51
0 2021/11/08 07:27:51
a bit of CAN hacking
a bit of CAN hacking
0 2022/06/14 20:34:35
0 2021/08/20 21:11:39
digging it out of the hole
digging it out of the hole
0 2022/06/14 20:34:37
as it sits today
as it sits today
0 2022/06/14 20:34:38
0 2022/08/08 20:36:00
driveshaft and PPF installed
driveshaft and PPF installed
0 2022/08/08 20:36:03
shifter position
shifter position
0 2022/08/08 20:36:03
removed rx8 header
removed rx8 header
0 2022/08/08 20:36:04
0 2021/08/20 21:11:38