RX8Club.com
replaced all the body panels
replaced all the body panels
0 2022/08/28 21:15:23
Rx8 harness
Rx8 harness
0 2021/08/20 21:11:36
NC harness
NC harness
0 2021/08/20 21:11:36
These studs need to come out of the PPF.
These studs need to come out of the PPF.
0 2021/09/13 17:25:00
Got this car running and driving over the winter
Got this car running and driving over the winter
0 2022/06/14 20:34:36
Bought a CSF #8066. need to fabricate mounts for it.
Bought a CSF #8066. need to fabricate mounts for it.
0 2021/10/23 10:52:24
one rx8 interior, disassembled
one rx8 interior, disassembled
0 2022/08/28 21:15:09
also started draping the wiring harnesses all together. This is going to take forever.
also started draping the wiring harnesses all together. This is going to take forever.
0 2021/09/25 13:20:01
0 2021/08/15 18:18:58
I used two NC PPF bolts backed up into either other
I used two NC PPF bolts backed up into either other
0 2021/09/13 17:25:01
0 2021/09/13 17:21:41
0 2021/08/20 21:11:38
cluster and dash also needed a bit of trimming, but this fit right together.
cluster and dash also needed a bit of trimming, but this fit right together.
0 2021/09/04 15:45:24
0 2022/08/28 21:15:21
The rx8 engine harness doesn't reach the NC ecu location, so i'll need to make or buy an extension harness
The rx8 engine harness doesn't reach the NC ecu location, so i'll need to make or buy an extension harness
0 2021/10/18 07:04:44
ready for disassembly
ready for disassembly
0 2022/08/22 05:48:06
parts car acquired
parts car acquired
0 2022/08/22 05:48:00
cleaned the garage up before starting more work
cleaned the garage up before starting more work
0 2022/08/08 20:36:02
checking fitment. the shifter hole needs to be made slightly wider.
checking fitment. the shifter hole needs to be made slightly wider.
0 2021/09/25 13:20:01
Rx8 Subframe with NC miata lower radiator mounts
Rx8 Subframe with NC miata lower radiator mounts
0 2021/08/25 13:52:55
NC PPF against the rx8 transmission
NC PPF against the rx8 transmission
0 2021/08/20 21:11:39
i am now, "bruh"
i am now, "bruh"
0 2022/08/28 21:15:15
NC ppf on the rx8 diff
NC ppf on the rx8 diff
0 2021/09/13 17:21:41
0 2021/08/15 18:19:00
New wheels and a swapped hardtop
New wheels and a swapped hardtop
0 2022/06/14 20:34:36
stripped clean
stripped clean
0 2022/08/28 21:15:25
Rx8 harness. more of the same
Rx8 harness. more of the same
0 2021/08/20 21:11:34
fully assembled dry run of the RX8 transmission and differential with an NC PPF and driveshaft
fully assembled dry run of the RX8 transmission and differential with an NC PPF and driveshaft
0 2021/09/13 17:21:42
some very epic wiring
some very epic wiring
0 2022/08/22 05:48:08
Both harness ready for joining
Both harness ready for joining
0 2021/08/25 13:52:57
0 2021/08/20 21:11:37
I was originally planning on using the oem NC airbox, but i decided it would take too much work, so i mocked up this idea. i'm not a huge fan of pod filters, but if i seal the box and plumb it into the oem rx8 snorkel, it'll be a proper "cold air intake"
I was originally planning on using the oem NC airbox, but i decided it would take too much work, so i mocked up this idea. i'm not a huge fan of pod filters, but if i seal the box and plumb it into the oem rx8 snorkel, it'll be a proper "cold air intake"
0 2021/10/18 07:04:51
harness removed
harness removed
0 2022/08/28 21:15:07
Loaded the engine and subframe up into the car
Loaded the engine and subframe up into the car
0 2021/09/25 13:20:02
not exactly sure why it seems to be so far to the left in this picture. the turret is slightly bound on the hole itself, so it's possible when i make the hole bigger, it will center itself in that dimension.
not exactly sure why it seems to be so far to the left in this picture. the turret is slightly bound on the hole itself, so it's possible when i make the hole bigger, it will center itself in that dimension.
0 2021/09/25 13:20:01
the rx8 fresh air tube fit with a bit of trimming. The NC airbox lines right up with it
the rx8 fresh air tube fit with a bit of trimming. The NC airbox lines right up with it
0 2021/10/04 19:23:14
Also picked up the K&N Typhoon intake. it fits pretty well, but i'm going to have to fabricate the sheet metal for the box as well.
Also picked up the K&N Typhoon intake. it fits pretty well, but i'm going to have to fabricate the sheet metal for the box as well.
0 2021/10/23 10:52:26
engine had to be lifted to do reposition the engine mounts
engine had to be lifted to do reposition the engine mounts
0 2022/08/08 20:36:01
WIP
WIP
0 2021/08/25 13:52:57
stripped the NC interior
stripped the NC interior
0 2022/09/02 20:53:38