Notices
Australia/New Zealand Forum They come from The Land Down Under.

Engine miss problem

Old Feb 24, 2009 | 08:27 PM
  #1  
GeoffJ's Avatar
Thread Starter
Registered User
 
Joined: Feb 2009
Posts: 128
Likes: 0
From: Melbourne, Australia
Engine miss problem

Hiya,

My cars been getting slight intermittent engine miss problemz at low rpm and idle speeds. Any ideas would be of use, thanks!

Regards,
Reply
Old Feb 24, 2009 | 08:30 PM
  #2  
Jedi54's Avatar
Administrator
iTrader: (7)
 
Joined: Mar 2004
Posts: 22,620
Likes: 3,487
From: The Dark Side
is it misfiring?
If so, most likely bad coils , plugs, or wires.
Reply
Old Feb 24, 2009 | 08:32 PM
  #3  
GeoffJ's Avatar
Thread Starter
Registered User
 
Joined: Feb 2009
Posts: 128
Likes: 0
From: Melbourne, Australia
thanks for quick reply..will further look into it. :D
Reply
Old Feb 24, 2009 | 08:32 PM
  #4  
Jedi54's Avatar
Administrator
iTrader: (7)
 
Joined: Mar 2004
Posts: 22,620
Likes: 3,487
From: The Dark Side
what exactly is the car doing?
Reply
Old Feb 24, 2009 | 08:33 PM
  #5  
thisllub's Avatar
Registered
 
Joined: Feb 2007
Posts: 325
Likes: 0
From: Northern NSW, Australia
What fuel are you using?
I find low octane fuel can cause flat spots.
Reply
Old Feb 24, 2009 | 08:42 PM
  #6  
GeoffJ's Avatar
Thread Starter
Registered User
 
Joined: Feb 2009
Posts: 128
Likes: 0
From: Melbourne, Australia
shell's, V-power............or MOBIL's high octane.
Reply
Old Feb 24, 2009 | 09:34 PM
  #7  
GeoffJ's Avatar
Thread Starter
Registered User
 
Joined: Feb 2009
Posts: 128
Likes: 0
From: Melbourne, Australia
Originally Posted by Jedi54
what exactly is the car doing?
yeah engine tends to misfire at idle speeds, any ideas on what likely causes this would be.

Is it a possiblity its to do with the seal? being paranoid lol.
Reply
Old Feb 24, 2009 | 09:38 PM
  #8  
Jedi54's Avatar
Administrator
iTrader: (7)
 
Joined: Mar 2004
Posts: 22,620
Likes: 3,487
From: The Dark Side
misfires at idle?
does the engine sputter? does the car shake a bit when it 'misfires'?
Usually misfires happen under load and at higher rpm's.

Could you describe in detail exactly what the car is doing at idle? is the Check Engine light on or flashing?

Sorry for all the questions, just trying to rule things out and help diagnose your car from the other side of the planet.
Reply
Old Feb 25, 2009 | 04:05 PM
  #9  
GeoffJ's Avatar
Thread Starter
Registered User
 
Joined: Feb 2009
Posts: 128
Likes: 0
From: Melbourne, Australia
yup. At idle speeds, then gets a little rough, as u accelerate the roughing fades.
Reply
Old Feb 25, 2009 | 11:07 PM
  #10  
Cromax's Avatar
Buzz Buzz Buzz
 
Joined: Mar 2005
Posts: 1,931
Likes: 0
From: Melbourne, Victoria
It's normal for the car to pop and burble when you first start it though.

If it's happening all the time (even after driving around a bit) it's either your spark plugs, wires, or coils.

Do you have any flat-spots about 4-5000rpm?
Reply
Old Feb 25, 2009 | 11:40 PM
  #11  
laythor's Avatar
I zoom therefore I am.
 
Joined: Mar 2007
Posts: 4,919
Likes: 12
From: San Jose, CA
don't mistake the pop of a normal rotary at idle to a misfire... you'll know if it's a misfire if you lose power in the 5k range like Cromax has said. I love the pop pop pop the 8 makes in the low revs.
Reply
Old Feb 26, 2009 | 12:49 AM
  #12  
takahashi's Avatar
New Member
 
Joined: Mar 2003
Posts: 9,944
Likes: 2
From: Melbourne, Australia
Originally Posted by GeoffJ
yup. At idle speeds, then gets a little rough, as u accelerate the roughing fades.
If you have a early year model or you have vibration shake in your gear stick, then check the sagging engine mounts.
Reply
Old Feb 26, 2009 | 04:26 PM
  #13  
GeoffJ's Avatar
Thread Starter
Registered User
 
Joined: Feb 2009
Posts: 128
Likes: 0
From: Melbourne, Australia
gear sticks, fine....it might be just what cromax said.. it does somewhat go pop, pop.....................haha
Reply
Old Feb 26, 2009 | 05:42 PM
  #14  
mikeyr's Avatar
i need a new photo
 
Joined: Jun 2004
Posts: 1,013
Likes: 0
From: Sydney
Geoff,

I'm still running the original plugs and coils at 56k but have spares (ready to change out). my problem was leads.

I put Magnecor leads on and my "rough idle" reduced by 95%. Even the missus commented unprompted! I'd checked the factory ones were well connected so must have just been poor quality.

Good luck

M
Reply
Old Feb 26, 2009 | 06:12 PM
  #15  
GeoffJ's Avatar
Thread Starter
Registered User
 
Joined: Feb 2009
Posts: 128
Likes: 0
From: Melbourne, Australia
very nice, I'll hopefully be able to look into this next week when i have the opportunity.

Thanks,
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
vapor2
West For Sale/Wanted
11
Nov 3, 2020 03:38 PM
Skyl3r
New Member Forum
148
Dec 2, 2019 04:51 PM
Davey's RX-8
Series I Trouble Shooting
0
Jul 28, 2015 12:13 PM
Belalnabi
New Member Forum
9
Jul 17, 2015 07:48 PM


Thread Tools
Rate This Thread
Rate This Thread:
You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -5. The time now is 03:09 PM.