Automatic RX8 transplanted rew engine in 2009
01-07-2022, 07:39 AM
#1
Registered
Thread Starter
Join Date: Feb 2019
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Automatic RX8 transplanted rew engine in 2009
我的车本来是09自动RX8，现在已经完成了重新移植，但是现在出现了哪里的问题。ABS不能工作。虽然A BS的故障灯不亮，但没有
表现出任何问题的线索。问题出在哪里？的现在是这样的？ ABS 需要启动制动，无论什么关闭事件，现在停止制动，或者没有我的步骤，ABS 不能被驱动。
Last edited by zephyrsms168; 01-07-2022 at 05:51 PM.
01-07-2022, 09:23 AM
#2
My car was originally a 09 automatic RX8, and now I have completed the transplant of rew, but now there is a problem. ABS will not work. Although the ABS fault light does not light up, there is no clue now. where is the problem?
The manifestation of the problem is like this. ABS needs the brake switch to be turned on to take effect. Now, no matter what happens, the brake or the step without me, the brake switch is always off and the ABS cannot be driven.
What ECU are you using?
There likely is some integration between the transmission controller and the ABS that needs imput. It doesn't occur with the MT ABS when you do the swap.
not sure if that helps much
The manifestation of the problem is like this. ABS needs the brake switch to be turned on to take effect. Now, no matter what happens, the brake or the step without me, the brake switch is always off and the ABS cannot be driven.
What ECU are you using?
There likely is some integration between the transmission controller and the ABS that needs imput. It doesn't occur with the MT ABS when you do the swap.
not sure if that helps much
01-07-2022, 09:27 AM
#3
Registered
Thread Starter
Join Date: Feb 2019
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
my car was originally a 09 automatic rx8, and now i have completed the transplant of rew, but now there is a problem. Abs will not work. Although the abs fault light does not light up, there is no clue now. Where is the problem?
The manifestation of the problem is like this. Abs needs the brake switch to be turned on to take effect. Now, no matter what happens, the brake or the step without me, the brake switch is always off and the abs cannot be driven.
what ecu are you using?
There likely is some integration between the transmission controller and the abs that needs imput. It doesn't occur with the mt abs when you do the swap.
Not sure if that helps much
The manifestation of the problem is like this. Abs needs the brake switch to be turned on to take effect. Now, no matter what happens, the brake or the step without me, the brake switch is always off and the abs cannot be driven.
what ecu are you using?
There likely is some integration between the transmission controller and the abs that needs imput. It doesn't occur with the mt abs when you do the swap.
Not sure if that helps much
01-07-2022, 05:18 PM
#5
Registered
Thread Starter
Join Date: Feb 2019
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
The stock ECU has been removed and the dash is the stock Mt. I need to consult my repairman about the wheel speed sensor reading and can setting。
01-07-2022, 05:39 PM
#6
Registered
Thread Starter
Join Date: Feb 2019
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
I tried to unplug the ECU and variable box ECU on an original 09 automatic, and the ABS can also work.
01-07-2022, 06:57 PM
#7
Does the car start properly? If so the Link must be sending something to the immobilizer to let it activate the starter circuit unless they wired around it.
There are so many places that this could be a problem it's difficult to give you much help.
Have you talked to Link techs? They were very good helping me set mine up.
There are so many places that this could be a problem it's difficult to give you much help.
Have you talked to Link techs? They were very good helping me set mine up.
Thread
Thread Starter
Forum
Replies
Last Post