{ FS } 2 Carbon Fiber vented Hoods: Seibon and VIS Racing
2 Carbon Fiber vented Hoods: Seibon and VIS Racing
Category: Exterior - Body Parts
Price: $1000
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): Series I, Series II
Location (US State/Canada/Int): CA
Item Condition: Used
- Seibon: SOLD
- VIS Racing: SOLD
- this is wrapped in clearbra for protection
Last edited by USAF_AV8R; Aug 26, 2025 at 08:37 AM.
I could bring these to SevenStock if anyone is going and wants to pick up. A $50 non-refundable deposit that’s applied to the purchase price would be required beforehand since they’d only fit in my truck that I otherwise wouldn’t use tomorrow.
Just notice that the second of the two styles has a cover below
the openings to keep the rain water off the engine. (I guess??)
Which is nice, but this design will only pull air from the front of the engine
not over the engine which defeats the purpose of having vents on the hood in the first place....
Or has my brain taken a short vacation??? ...
the openings to keep the rain water off the engine. (I guess??)
Which is nice, but this design will only pull air from the front of the engine
not over the engine which defeats the purpose of having vents on the hood in the first place....
Or has my brain taken a short vacation??? ...
Just notice that the second of the two styles has a cover below
the openings to keep the rain water off the engine. (I guess??)
Which is nice, but this design will only pull air from the front of the engine
not over the engine which defeats the purpose of having vents on the hood in the first place....
Or has my brain taken a short vacation??? ...
the openings to keep the rain water off the engine. (I guess??)
Which is nice, but this design will only pull air from the front of the engine
not over the engine which defeats the purpose of having vents on the hood in the first place....
Or has my brain taken a short vacation??? ...

Not to be a hard nose here but it looks like the "cover " (catch pan) is attached with pop rivets.
The "on - off" plan could be a pain in the you know what...
But, if the buyer installed "rivnuts" it would be doable....
As in:
The "on - off" plan could be a pain in the you know what...
But, if the buyer installed "rivnuts" it would be doable....
As in:
I’ll be driving from southern California (north of L.A.) to northern California (Bay-ish area) and be there from 24-26 Dec. I could bring one or both hoods for folks that live there or are along the route. There is a $100 non-refundable fee to cover fuel to be paid in advance since I’d be using my truck that I otherwise wouldn’t drive.
I’ll be driving from southern California (north of L.A.) to northern California (Bay-ish area) and be there from 24-26 Dec. I could bring one or both hoods for folks that live there or are along the route. There is a $100 non-refundable fee to cover fuel to be paid in advance since I’d be using my truck that I otherwise wouldn’t drive.
Not to be a hard nose here but it looks like the "cover " (catch pan) is attached with pop rivets.
The "on - off" plan could be a pain in the you know what...
But, if the buyer installed "rivnuts" it would be doable....
As in:
https://www.amazon.com/Screw-Stainle.../dp/B08GFLY8JG
The "on - off" plan could be a pain in the you know what...
But, if the buyer installed "rivnuts" it would be doable....
As in:
https://www.amazon.com/Screw-Stainle.../dp/B08GFLY8JG
-R3dream
[QUOTE=R3Dream;4990509]Any Chance you'll be doing this again in the spring/summer?
I could. I’m repositioning to spend more time in Cali in a few months. It’d be faster and probably cheaper in gas for you to drive down without a hood, install it on your car, then drive up.
I could. I’m repositioning to spend more time in Cali in a few months. It’d be faster and probably cheaper in gas for you to drive down without a hood, install it on your car, then drive up.
Thread
Thread Starter
Forum
Replies
Last Post
tito rotativo
RX-8 Parts For Sale/Wanted
19
Apr 19, 2008 05:03 PM
tito rotativo
RX-8 Parts For Sale/Wanted
3
Oct 30, 2007 06:51 PM




