{ FS } 2004 RX-8 Roller and Rebuilt Motor 0 Miles BHR Ignition
#1
Registered
Thread Starter
iTrader: (1)
Join Date: Sep 2013
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
2004 RX-8 Roller and Rebuilt Motor 0 Miles BHR Ignition
I can't post this in main section yet, so we will see if we can do it here. Been lurking, reading and trying to rebuild my 8 but now its time to let it go for a different project
I have a 2004 RX-8 Sunlight Silver Grand Touring 6MT roller. 129xxx miles. Has transmission, rear end, etc. All but motor and accessories. Dent on both driver side doors, and above driver door. Has cracked front and rear bumpers and needs new driver side front fender. Straight Frame, clean title, good interior with minor wear. Just needs some TLC.
-SOLD
2004 6-port motor -SOLD
New in box BHR ignition, never installed -SOLD
Call/text/PM/email with questions. Since I've been a member but not enough posts I suppose this can be local pickup only.
I have everything to make one total car, will sell everything in one move if desired.
Thanks,
Zane Piper
678-207-6687
I have a 2004 RX-8 Sunlight Silver Grand Touring 6MT roller. 129xxx miles. Has transmission, rear end, etc. All but motor and accessories. Dent on both driver side doors, and above driver door. Has cracked front and rear bumpers and needs new driver side front fender. Straight Frame, clean title, good interior with minor wear. Just needs some TLC.
-SOLD
2004 6-port motor -SOLD
New in box BHR ignition, never installed -SOLD
Call/text/PM/email with questions. Since I've been a member but not enough posts I suppose this can be local pickup only.
I have everything to make one total car, will sell everything in one move if desired.
Thanks,
Zane Piper
678-207-6687
Last edited by Zane98S14; 03-04-2014 at 01:54 PM. Reason: Ignition Sold
#2
Registered
Thread Starter
iTrader: (1)
Join Date: Sep 2013
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
I'll give this a bump going into the weekend.
Also have a Sohn Adapter from Rotary Aviation SOLD. Still shrink wrapped from RA, never used/opened/installed.
Also doesn't hurt to keep upping post count so I can eventually sell in general.
Thanks,
Zane
Also have a Sohn Adapter from Rotary Aviation SOLD. Still shrink wrapped from RA, never used/opened/installed.
Also doesn't hurt to keep upping post count so I can eventually sell in general.
Thanks,
Zane
Last edited by Zane98S14; 01-06-2014 at 07:43 AM. Reason: SOHN sold
#11
Registered
Thread Starter
iTrader: (1)
Join Date: Sep 2013
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Bump. Motor sale pending. Have started bolting body panels back on the car and take it off jack stands. New pictures will be up by the weekend.
Wife is getting real antsy to get car out of garage, someone pick this up.
I also have 2 of everything bolted to motor when removed including: upper and lower intake manifold, OMP w/ lines and nozzles, fuel injectors, rails, exhaust manifolds, engine harness, etc. If you need anything, let me know. NEED IT ALL GONE.
Will start another thread for all that stuff once i get it all out and photographed.
-Zane
Wife is getting real antsy to get car out of garage, someone pick this up.
I also have 2 of everything bolted to motor when removed including: upper and lower intake manifold, OMP w/ lines and nozzles, fuel injectors, rails, exhaust manifolds, engine harness, etc. If you need anything, let me know. NEED IT ALL GONE.
Will start another thread for all that stuff once i get it all out and photographed.
-Zane
Thread
Thread Starter
Forum
Replies
Last Post
cschoeps
RX-8's For Sale/Wanted
0
08-06-2015 12:44 PM
N0P1st0ns
Series I Aftermarket Performance Modifications
4
07-30-2015 09:45 AM
dbarber
Series I Trouble Shooting
14
07-25-2015 01:34 PM