Flooding: ECU pedal-to-floor fuel cut vs. installing a fuel cut switch?
Thread Starter
Registered
Joined: Feb 2016
Posts: 18
Likes: 0
Flooding: ECU pedal-to-floor fuel cut vs. installing a fuel cut switch?
Hello all,
As some quick background, I am a new rx-8 owner, just bought an 05 sport model sunlight silver, 100% stock. I have owned an 88 rx-7 TII for about 15 years now so have been through it all, so obviously I have a well earned concern for flooding! On my rx-7 I installed a fuel cut switch similar to "rotaryresurection's" write up, and this fuel cut switch has never once let me down in the face of flooding, it worked every single time I needed to use it. Now With my new rx-8 I have had no starting issues, cold or hot, but obviously I want to take all precautions ahead of time. I've already orded the BHR ignition coil pack. The battery tests well and the started clocked at 280 rpm in my compression test so I think those two components are ok. This all brings me to the title question: is the built-in fuel-cut (pedal to floor) in the rx-8 a reliable anti flooding method? Or is there benefit to adding a fuel cut switch?
I'm hoping to hear from anyone that has actually used the pedal to floor method. In my searches I've found that most people say it did not help them, and they end up yanking the fuel pump/circuit fuse anyway, which is just the same thing as a fuel cut switch but without the ability to control it while cranking. In this post "http://https://www.rx8club.com/serie...6/#post4379682" "Darkning" says
Can anyone else verify that the ecu functions this way with the pedal depressed?
I will likely install a fuel cut switch on my 8 in time as a precaution, but was hoping to get some insight from those of you who have used the built in fuel cut system, thanks!
As some quick background, I am a new rx-8 owner, just bought an 05 sport model sunlight silver, 100% stock. I have owned an 88 rx-7 TII for about 15 years now so have been through it all, so obviously I have a well earned concern for flooding! On my rx-7 I installed a fuel cut switch similar to "rotaryresurection's" write up, and this fuel cut switch has never once let me down in the face of flooding, it worked every single time I needed to use it. Now With my new rx-8 I have had no starting issues, cold or hot, but obviously I want to take all precautions ahead of time. I've already orded the BHR ignition coil pack. The battery tests well and the started clocked at 280 rpm in my compression test so I think those two components are ok. This all brings me to the title question: is the built-in fuel-cut (pedal to floor) in the rx-8 a reliable anti flooding method? Or is there benefit to adding a fuel cut switch?
I'm hoping to hear from anyone that has actually used the pedal to floor method. In my searches I've found that most people say it did not help them, and they end up yanking the fuel pump/circuit fuse anyway, which is just the same thing as a fuel cut switch but without the ability to control it while cranking. In this post "http://https://www.rx8club.com/serie...6/#post4379682" "Darkning" says
For those of you wondering... You don't need to taper off the accel pedal as it feels like its going to start. Once the engine goes into "running" mode the pedal goes from cutting the fuel to supplying it. At that point your revs will be way up there and you can release or modulate your throttle as needed to keep it running until it clears up.
I re-flooded my car twice yesterday trying to let off the gas pedal when I thought it was going to start and it puttered back out. Holding the pedal down until I knew for a fact it was running at 5/6k rpm did the trick.
I re-flooded my car twice yesterday trying to let off the gas pedal when I thought it was going to start and it puttered back out. Holding the pedal down until I knew for a fact it was running at 5/6k rpm did the trick.
Can anyone else verify that the ecu functions this way with the pedal depressed?
I will likely install a fuel cut switch on my 8 in time as a precaution, but was hoping to get some insight from those of you who have used the built in fuel cut system, thanks!
Trying repeatedly to start it?
Both times with mine I smelled fuel and stopped.
One was a bad coil, and the other a weak battery.
I think it's a bit of a moot point. A healthy car with all the latest (~2007 vintage) software updates should not flood and you've got the BHR kit on the way, which is good. An unhealthy car could flood, but by that point you've missed something important in your maintenance, so focus on preventing that.
Thread Starter
Registered
Joined: Feb 2016
Posts: 18
Likes: 0
I think it's a bit of a moot point. A healthy car with all the latest (~2007 vintage) software updates should not flood and you've got the BHR kit on the way, which is good. An unhealthy car could flood, but by that point you've missed something important in your maintenance, so focus on preventing that.
Registered
Joined: Oct 2017
Posts: 612
Likes: 61
From: South Central PA
S2 pump swap and call it a day. but if you only experience this at 1/4 tank before, and now at 1/2, then it's probably the pump start going out. if you dont care about fuel starve at 1/4 and just want and cheap and fast solution, then just replace the S1 pump. if you want a better solution, then do the s2 pump swap.
S2 pump swap and call it a day. but if you only experience this at 1/4 tank before, and now at 1/2, then it's probably the pump start going out. if you dont care about fuel starve at 1/4 and just want and cheap and fast solution, then just replace the S1 pump. if you want a better solution, then do the s2 pump swap.
Posted in the wrong thread maybe?
Thread
Thread Starter
Forum
Replies
Last Post
SSJ 909
RX-8 Discussion
10
Apr 10, 2006 08:26 PM
