I stronly urge you to go to another dealership. (after reading about what your Techs are saying)

I just dig up the parts info for their *on order* parts.


F151-73-771F :
the last word is F, not 1, and its the weather strip, AKA rubber door seal for the driver side

FE62-16-510C :
Now I wonder why are they ordering another clutch release bearing aka throwout bearing, I just changed mine like couple hundred miles ago. all I asked was to replace the CLUTCH RELEASE CUT SWITCH, the one right behind the fuxking clutch pedal. NOT BEARING !!! WTF ?! I even had the TSB with me and they looked at it ....

N326-11-D03 :
D03 not 003, and this is the PLIOT BEARING .... lol, I just had my clutch changed now I wonder what they gonna say when they see my new flywheel + clutch

KL0118741 :
I missed this number before, this number pulled up a bunch of stuff but they all have the same price and almost the same description ... all Solenoid and it cost less than 60 bucks each ~~~ they're actually that cheap? damn, I thought its alot more expensive.

F184-44-010 :
I cant find this one, I probably just cant *decrypt* his hand writing and got the wrong number.

All these parts are freaking cheap, why are they making it such a big fuss about it ~

I mean come on I say it should take them no longer than 5 hours to finish everything. Big freaking deal. Damn stupid Mazda techs. I just told them I had some *noise when I step on my clutch* , shown them the TSB printout and they still got it wrong ..... damn retards.

I was thinking of the same thing, but they already took a picture so I guess Im just going to wait for an answer.

If its bad news, I will have to fight with Mazda.

If its good news .... then :rock: , go back to this dealership, to get everything fix. then I will never show up again.

under the law, they can only void the warranty of parts that were hurt by the aftermarket mod, futhermore they have to prove it was the mod.

everything else, besides what was directly effected by the mod is still under warrant

magnuss moss act, or some thing like that, i cant recall the name, its all over the forum though. . . . .

good luck, dont take no sh*t from anybody, take no prisoners! :101384_l:

I disconnected the vacuumm line from the VFAD which runs to the underside of the intake manifold and then capped with a vacuum nipple cap which I purchased from Pepboys or Checker Auto Parts.

Then I tucked the VFAD connector up close to the strut brace so it doesn't draw attention.

;)

They sell those nipple cap at Pepboys ?

Shit, Im gonna go there now and ask !

Exactly

Like I said before, I want *prove* , not the tech's mouth or *cuz mazda said so*

If they give me shit I will start a lawsuit trust me. Its good to have an attorney as your buddy :) I just need to pay him a case of beers :P

They'd be perfect for your 89 Civic.
:ylsuper:

lol !!!

Oh yes I found some at Pepboys ! but havent had a chance to install it yet. Might as well do it now :P

Glad to have helped.

:smoker:

I installed the nipples.

Threw that stupid plastic tube away (actually Im gonna keep it in my garage)

Thx man :)

Yep, it doesn't hurt to put a small zip tie on it to ensure it doesn't leak any air. The car doesn't idle as well when there is a leak. :)

Really .... let me drive for a few days and see what happens.

Just an FYI the Mazdaspeed Cold Air Intake does not use this plug or the vacum line that goes to the under side of the throtle body. So I would use that as some amunition.

Thats what Im thinking, I dont have any experience with Mazdaspeed/AEM CAI :(

but I will keep that in mind. I dont have time to call this dumb dealership yet. Might as well do it tomorrow.

I'll keep you guys post.

to help you there is a crazy vdaf code that comes up... it does not make the light go off. but can happen..

it would do the same thing with the ms intake. dont ask me how i know and i dont have the ms intake..

knowledge is power..

beers :beer:

Thats true. I get this CEL because the Computer is not detecting shit from the solenoid. I got this CEL even before I disconnect it. I guess most Mazda tech just dont know jack about how this car works.

I will call tomorrow and see what kind of shit they gonna say.

pm me on this i can give some insight.


beers :beer:

Those asswipes I left a msg couple of times but no one call me back.

I might have to go there just to yell the crap out of them, man .... I hate dealerships.

I had a similar experience where the dealer would not reflash due to the RB cold air intake system and the Mazport cooling mod. We went around and around on "the law". I contacted Mazda and they refused to get involved with the dealer but they did tell me if I removed the mods and put back as stock that the dealer would give me the reflash and check my other engine related complaints (non engine complaints were repaired on first trip). So I went back to the dealer and had the tech come out to show me what he considered "mods" as I was not going to be a happy camper if the made me remove the RB catback, RP super cat, coolers or suspension parts. In short to get the reflash I had to remove the RB cold air intak and Mazport cooling mod. You may have to do the same.

Your easy to avoid on the phone - personal contact is the only way - keep your temper down.

Well the thing here is that the CEL was not really a problem, I have that CEL because one of the useless part (the little crap for the VFAD, SSV solenoid) was disconnected completely.

Why would I want it to be disconnected ? First of all its completely useless, second of all I have the same CEL even before I disconnect it.

If they dont give it to me, its fine, but Im just piss about their Tech's attitude, I already kept my temper down, if I didnt I think yell the crap out of them already.

I dont even feel like to call them anymore. I might just go to another dealership(closer one) and talk to them, see what they say.