Torque (Android app) AFR for the RX8?
Hi,
Do any of you know how to add the AFR dial to the "Torque" Android app? The program allow you to add custom PIDs adding the hex code, minimum and maximum values, scale factor and equation, but I've no idea what would be the values for the AFR for the RX8 (googled it but could not find anything). Thanks. |
AFR values are pretty much the same for all cars, you can just put 0 to 30 or so to have a decent scale on it.
It will be about 13-14 for cruise, 11 for pedal to the metal and 20+ for foot off gas. |
Originally Posted by neXib
(Post 3919710)
AFR values are pretty much the same for all cars, you can just put 0 to 30 or so to have a decent scale on it.
It will be about 13-14 for cruise, 11 for pedal to the metal and 20+ for foot off gas. |
Found it!
http://www.ozmpsclub.com/forum/tech-...azda-pids.html I'm pasting them here too, for convenience: PIDS that work out of the box with Torque: Load Fuel Level RPM Intake Temp Intake manifold pressure(in kPa) Coolant Temp Vacuum/Boost Gauge Barometric Pressure Mass air flow rate(in g/s not voltage) Throttle Position Timing Advance(Works, at WOT shows near 0 degrees. Yay stock tune!) Enhanced PIDs you have to manually enter Long name & short name can be whatever you want. I tried to stick to conventional names. LTFT Long Term Fuel Trim? OBD2 PID: 0107 Long Name: LTFT Short Name: LTFT Minimum Value: -25 Maximum Value: 25 Scale Factor: x1 Unit Type: % Equation: (A-128)*100/128 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: STFT Short Term Fuel Trim? OBD2 PID: 0106 Long Name: STFT Short Name: STFT Minimum Value: -25 Maximum Value: 25 Scale Factor: x1 Unit Type: % Equation: (A-128)*100/128 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Fuel Pressure OBD2 PID: 0123 Long Name: FP Short Name: FP Minimum Value: 0 Maximum Value: 2500 Scale Factor: x1 Unit Type: % Equation: (A*256+B)*10*.145 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Open Loop Commanded Air/Fuel Ratio OBD2 PID: 0144 Long Name: AFR Short Name: AFR Minimum Value: 0 Maximum Value: 20 Scale Factor: x1 Unit Type: A/F Equation: (A*256+B)/32768*14.7 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: OEM Wideband Air/Fuel Ratio OBD2 PID: 0134 Long Name: WAFR Short Name: WAFR Minimum Value: 0 Maximum Value: 20 Scale Factor: x1 Unit Type: A/F Equation: (A*256+B)/32768*14.7 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Cat Temp OBD2 PID: 013c Long Name: Cat Temp Short Name: Cat Temp Minimum Value: 0 Maximum Value: 2000 Scale Factor: x1 Unit Type: F Equation: ((A*256+B)/10-40)*1.8+32 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Absolute Load OBD2 PID: 0143 Long Name: Abs Load Short Name: Abs Load Minimum Value: 0 Maximum Value: 255 Scale Factor: x1 Unit Type: % Equation: (A*256+B)*100/255 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: Intake Manifold Absolute Pressure OBD2 PID: 010b Long Name: IMAP Short Name: IMAP Minimum Value: 0 Maximum Value: 100 Scale Factor: x1 Unit Type: PSI Equation: A*.145 Gen 1 Status: Gen 2 Status: Working and confirmed MS6 Status: |
Cool, thanks
|
Agreed now people don't have to get accessport if they just want to reset CEL. Good find, I didn't even know about this.
|
Originally Posted by Domenico
(Post 3920273)
Agreed now people don't have to get accessport if they just want to reset CEL. Good find, I didn't even know about this.
|
Well theirs a lot of people that come on here wondering what they can do to clear CELs. The only replys they get is accessport. Access port is a great thing to have but if your just looking for a way too keep your CEL off this is it also the other attributes the app has.
|
fyi, the 8 does not have a way to measure fuel pressure. Just tested all the other PID's and they're working fine with Torque
nice to see AFR's without having to plug in my access port. |
how does this work with out a cable? I know there is probably an OBDII port but just woundering if there is a cable out there, i have the Droid2 so hey a $4 app + cable sure beats standalone to check things lol
|
bluetooth dongle plugs into your obdii port.. phone reads that through bt naturally :)
|
Originally Posted by laythor
(Post 3923321)
bluetooth dongle plugs into your obdii port.. phone reads that through bt naturally :)
|
I was thinking on leaving the OBDII bluetooth dongle always connected, but I've noticed that the car always provide energy even if the contact is off and I fear to drain the battery; the dongle I have ("PLX Kiwi") doesn't seem to auto turn off (I waited for 10 minutes).
|
I have the kiwi dongle and just turn off the switch on it when i get out of the car.
|
Originally Posted by Domenico
(Post 3920281)
Well theirs a lot of people that come on here wondering what they can do to clear CELs. The only replys they get is accessport. Access port is a great thing to have but if your just looking for a way too keep your CEL off this is it also the other attributes the app has.
|
I have obd2 cabel bt i don't have the tune softwear can any one give me the link or name of the software where i can tunemy rx8....
|
I have the Kiwi BT dongle and I leave it connected 24/7 and don't turn it off. Its been that way for 6 months now and my battery's fine.
Also, its true that these adapters will only clear the CEL until you turn the car off and back on again. |
I've had the ODB+Key as the dongle for a while now, though I use it more on my other cars than the 8 (since I also have the AP). I've found that it doesn't like the 8 all that much. Plugging in the dongle and opening the app disables my TCS/DSC. Have to disconnect and remove the dongle and power off the car before it will recognize it again.
Anyone else seen this? No issues at all on my Mazda5 or my Miata. |
Originally Posted by RIWWP
(Post 4027863)
I've had the ODB+Key as the dongle for a while now, though I use it more on my other cars than the 8 (since I also have the AP). I've found that it doesn't like the 8 all that much. Plugging in the dongle and opening the app disables my TCS/DSC. Have to disconnect and remove the dongle and power off the car before it will recognize it again.
Anyone else seen this? No issues at all on my Mazda5 or my Miata. |
It looks like one of the most recent updates brought A/FR support natively to Torque.
|
[QUOTE=Also, its true that these adapters will only clear the CEL until you turn the car off and back on again.[/QUOTE]
I use the Torque app, with a BT android phone, when i clear the CEL it actually goes away until the problem occurs once more. For eg: I had a P2405 code, cleared it but came back on a week later, cleared again, came back on a around 3 days after that..Unless someone has a serious problem that the CEL won't clear |
Sorry to thread revive but I figured this would be a good place to ask since the custom PIDs are listed.
Is there any way to get an oil pressure gauge on Torque? The one that comes with the program doesn't read. |
there is no oil pressure reading on the canbus so no you cannot.
|
dashcommand recognizes all the mazda pids out of the box and has a better skin than torque imho
|
Originally Posted by ShellDude
(Post 4220948)
dashcommand recognizes all the mazda pids out of the box and has a better skin than torque imho
|
All times are GMT -5. The time now is 11:40 AM. |
© 2024 MH Sub I, LLC dba Internet Brands