side aero flare
#3
Still lovin' it...
Join Date: Oct 2003
Location: Colorado, From Utah originally
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
side aero flares...
I have installed the side aero flares, but I didn't put a DIY together because the directions were pretty straight-forward.
If you do not have the directions, I wouldn't try the install. This is because there are holes you need to drill into the side of the vehicle, and you really need the paper templates that are provided in the instructions. Proper fitment can be seriously compromised if you're even just a little bit off.
Otherwise, cut the rock-shield, drill your holes with the templates, clip in the clips, and you're good to go. Another note to keep in mind is the tape. REALLY make sure you've cleaned the surfaces well (especially under the side panel where it adheres closest to the front of the car, I've seen a lot of people's side flares peeling off there).
Is there anything specific you're looking for on the installation of these?
--Landon
If you do not have the directions, I wouldn't try the install. This is because there are holes you need to drill into the side of the vehicle, and you really need the paper templates that are provided in the instructions. Proper fitment can be seriously compromised if you're even just a little bit off.
Otherwise, cut the rock-shield, drill your holes with the templates, clip in the clips, and you're good to go. Another note to keep in mind is the tape. REALLY make sure you've cleaned the surfaces well (especially under the side panel where it adheres closest to the front of the car, I've seen a lot of people's side flares peeling off there).
Is there anything specific you're looking for on the installation of these?
--Landon
Last edited by Landon_Starr; 04-21-2004 at 08:43 PM.
#5
Registered User
Join Date: Feb 2003
Location: Long Island
Posts: 581
Likes: 0
Received 0 Likes
on
0 Posts
you drill into the side of your car along the bottom. if you want to call that a vertical surface, then yes.
the instructions are pretty straightforward, but drilling into your car is always risky and a little scary.
the instructions are pretty straightforward, but drilling into your car is always risky and a little scary.
#6
Still lovin' it...
Join Date: Oct 2003
Location: Colorado, From Utah originally
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, what he said.
With the templates the drill holes are pretty easy to place. I'd suggest taping them to the side aero flares, then putting another piece(stickier than the one taped to the flare) and pushing the flare onto the car where it's supposed to be. The tape on the side aero flare will pull off, but will stick to the car. I found this the easiest way to locate the drilling point with the lowest amount of anxiety about drilling into my car.
--Landon
With the templates the drill holes are pretty easy to place. I'd suggest taping them to the side aero flares, then putting another piece(stickier than the one taped to the flare) and pushing the flare onto the car where it's supposed to be. The tape on the side aero flare will pull off, but will stick to the car. I found this the easiest way to locate the drilling point with the lowest amount of anxiety about drilling into my car.
--Landon
Originally posted by RX8Lover
you drill into the side of your car along the bottom. if you want to call that a vertical surface, then yes.
the instructions are pretty straightforward, but drilling into your car is always risky and a little scary.
you drill into the side of your car along the bottom. if you want to call that a vertical surface, then yes.
the instructions are pretty straightforward, but drilling into your car is always risky and a little scary.
#9
Registered
iTrader: (2)
Join Date: Mar 2004
Location: columbus, oh
Posts: 861
Likes: 0
Received 0 Likes
on
0 Posts
landon, im getting scared here buddy! im going to have to locate those templates!!! seriously though, im looking forward to getting them, if you can give me some recomendations on how you did the double tape thing id appreciate it!
#10
Still lovin' it...
Join Date: Oct 2003
Location: Colorado, From Utah originally
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
LoL. I figured you'd be chiming in here sometime, Kellybrf. It's really not a difficult procedure with the instructions and templates. It's just a matter of time before someone can scan & post. Otherwise, I'm sure Trussville or Rosenthal would be able to provide copies.
--Landon
--Landon
Originally posted by kellybrf
landon, im getting scared here buddy! im going to have to locate those templates!!! seriously though, im looking forward to getting them, if you can give me some recomendations on how you did the double tape thing id appreciate it!
landon, im getting scared here buddy! im going to have to locate those templates!!! seriously though, im looking forward to getting them, if you can give me some recomendations on how you did the double tape thing id appreciate it!
#11
Still lovin' it...
Join Date: Oct 2003
Location: Colorado, From Utah originally
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by kellybrf
if you can give me some recomendations on how you did the double tape thing id appreciate it!
if you can give me some recomendations on how you did the double tape thing id appreciate it!
--Landon
#13
Still lovin' it...
Join Date: Oct 2003
Location: Colorado, From Utah originally
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, that was kinda nerve racking. Especially the drilling part. HOWEVER, the nice thing is that the holes are covered by the kit, so really all you need to do is make sure the clips fit in the holes, doesn't matter what they look like.
Just a tip, start small and go big with the drill bits. Nothing worse than to drill your hole and find out the clip is loose. Can always make the hole bigger, making it smaller is a bit perplexing. :D
--Landon
Just a tip, start small and go big with the drill bits. Nothing worse than to drill your hole and find out the clip is loose. Can always make the hole bigger, making it smaller is a bit perplexing. :D
--Landon
#14
Still lovin' it...
Join Date: Oct 2003
Location: Colorado, From Utah originally
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by kellybrf
but loose enough so the other side sticks to the car
but loose enough so the other side sticks to the car
There's a good possibility others have found easier ways to handle this issue, too. Putting a paint or something on the flare clip then pushin it up against the car (since it will be hidden) might be another tactic to think about. I'm sure there's a million easier ways than the way I did it. I was too excited to get it on, so my creativity was somewhat low that day. :D
--Landon
Thread
Thread Starter
Forum
Replies
Last Post
Jst4fun
RX-8 Parts For Sale/Wanted
18
04-17-2021 07:43 AM
SimonT182
RX-8 Parts For Sale/Wanted
4
10-02-2015 10:33 AM
jasonrxeight
RX-8's For Sale/Wanted
2
09-30-2015 01:53 PM