Rear Bumper Grills
#4
Registered User
Join Date: Aug 2004
Location: Ft. Bragg, NC
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
I would say to go ahead and cut out the existing black plastic area where you put the mesh. and mount the aluminum mesh behind it, then cut the heat sheild around the backside of the muffler, exposing the muffler canisters from the back of the car. trust me it looks really good. Thats what I did. On the front and rear bumper cover. I got rid of the plastic grills.
#6
Bipolar Member
Join Date: Dec 2003
Location: Laredo, Texas
Posts: 747
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by superscout03
I would say to go ahead and cut out the existing black plastic area where you put the mesh. and mount the aluminum mesh behind it, then cut the heat sheild around the backside of the muffler, exposing the muffler canisters from the back of the car.
#7
Registered Lunatic
iTrader: (1)
Originally Posted by Rotary Rasp
I took the extra mesh from my oil cooler girlls and made this. What do you guys think?
Do you think it would look better or worse with the rotary accent?
#9
503wtq Boosted Bimmer
Thread Starter
iTrader: (2)
Join Date: Oct 2004
Location: Los Angeles, California
Posts: 3,038
Likes: 0
Received 0 Likes
on
0 Posts
It wasn't hard to attach it. There is already a hole on each side. I had to drill another hole on either side of the car. (two holes per side) Then I slipped a wire tie from the back around the mesh and back out the back side where I spliced it together. It pretty easy to do.
#15
503wtq Boosted Bimmer
Thread Starter
iTrader: (2)
Join Date: Oct 2004
Location: Los Angeles, California
Posts: 3,038
Likes: 0
Received 0 Likes
on
0 Posts
That info is in this thread:
https://www.rx8club.com/series-i-exterior-appearance-body-kits-27/home-depot-oil-cooler-guards-52179/
https://www.rx8club.com/series-i-exterior-appearance-body-kits-27/home-depot-oil-cooler-guards-52179/
#16
Registered User
That looks awesome, I was thinking of doing that too, but never got around to it. I think I might just have to do it! The rotary accent sets it off very nicely. And...you need a new plate, I had a "5KRF..." plate haha, what can "KRF" stand for?! nothing! nice job though on the mesh
#18
503wtq Boosted Bimmer
Thread Starter
iTrader: (2)
Join Date: Oct 2004
Location: Los Angeles, California
Posts: 3,038
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by nomopistons
I just did the same thing this weekend using aluminum gutter mesh. Total cost was 2.25
#19
Originally Posted by superscout03
I would say to go ahead and cut out the existing black plastic area where you put the mesh. and mount the aluminum mesh behind it, then cut the heat sheild around the backside of the muffler, exposing the muffler canisters from the back of the car. trust me it looks really good. Thats what I did. On the front and rear bumper cover. I got rid of the plastic grills.
#20
Registered User
Join Date: Jun 2004
Location: Milwaukee, WI.
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
Rotary Rasp, I see your RX-8 badge in your avatar but not on your car...Why did you remove it?
I was thinkin of doin the opposite, removing the Mazda and logo badges and leaving the RX-8 badge.
I was thinkin of doin the opposite, removing the Mazda and logo badges and leaving the RX-8 badge.
#21
503wtq Boosted Bimmer
Thread Starter
iTrader: (2)
Join Date: Oct 2004
Location: Los Angeles, California
Posts: 3,038
Likes: 0
Received 0 Likes
on
0 Posts
You can't remove the Mazda emblem because it has holes in the trunk to hold it on. The RX-8 emblem is the only one on the entire car that uses only doubled sided tape. You can however move the RX-8 badge to the drivers side of the car and cover up the holes from the Mazda badge. ....and I removed it because I could.:D
#22
Gets the WORST mpg
iTrader: (1)
Join Date: Jul 2008
Location: Missouri
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
I put some gutter mesh over the black plastic mesh area of my rear bumper too!
Before
Uploaded with ImageShack.us
After
Uploaded with ImageShack.us
Before
Uploaded with ImageShack.us
After
Uploaded with ImageShack.us