Front Bumper Removal
#1
Registered
Thread Starter
Join Date: May 2009
Location: Lethbridge, Alberta, Canada
Posts: 206
Likes: 0
Received 0 Likes
on
0 Posts
Front Bumper Removal
So I decided to put grilles on the front bumper. Just in the bottom center and over the oil coolers (they were taking a beating). The instructions that came with the grilles were fine for taking off the basic bumper, but when it came to the part about fog lights and headlight cleaners it has no explanation on how to remove them to be able to separate the bumper from the car. I looked around a bit but didn't have much luck finding out how.
Does anyone know how you're suppose to take off the fog lights and headlight cleaners from the bumper properly? I think I spotted about 4 screws (for each side) that would let both parts come completely off the bumper. Is that right? Those'll be a pain to get back on later that way...
Does anyone know how you're suppose to take off the fog lights and headlight cleaners from the bumper properly? I think I spotted about 4 screws (for each side) that would let both parts come completely off the bumper. Is that right? Those'll be a pain to get back on later that way...
#4
Registered
Thread Starter
Join Date: May 2009
Location: Lethbridge, Alberta, Canada
Posts: 206
Likes: 0
Received 0 Likes
on
0 Posts
Thanks, that diagram helped for the washers. I didn't quite know where I should have been making the separation. Those fog lights though, I could find the connector just no way of actually taking it off unless I forced it. It'll have to wait for tomorrow now though, its dark out! Thanks for the fast reply!
#5
I thought the fogs were a bitch. I think the tab is on the inside. push in to release.
The tab is only on one side.
There is something in the DIY section but it will be a search.
The tab is only on one side.
There is something in the DIY section but it will be a search.
#8
Grasshopper
iTrader: (1)
I guess I still don't see the issue with just leaving the fog lights on the bumper and disconnecting the wire harness
Everytime I pull my bumper off, that's all I do.
Once I remove all the fasteners and bolts, I pull the whole bumper out slightly (since the wires for the fog lights aren't that long) and reach down and disconnect them.
But to each their own. Whatever works for you.
Everytime I pull my bumper off, that's all I do.
Once I remove all the fasteners and bolts, I pull the whole bumper out slightly (since the wires for the fog lights aren't that long) and reach down and disconnect them.
But to each their own. Whatever works for you.
#9
Registered
Thread Starter
Join Date: May 2009
Location: Lethbridge, Alberta, Canada
Posts: 206
Likes: 0
Received 0 Likes
on
0 Posts
I guess I still don't see the issue with just leaving the fog lights on the bumper and disconnecting the wire harness
Everytime I pull my bumper off, that's all I do.
Once I remove all the fasteners and bolts, I pull the whole bumper out slightly (since the wires for the fog lights aren't that long) and reach down and disconnect them.
But to each their own. Whatever works for you.
Everytime I pull my bumper off, that's all I do.
Once I remove all the fasteners and bolts, I pull the whole bumper out slightly (since the wires for the fog lights aren't that long) and reach down and disconnect them.
But to each their own. Whatever works for you.
Thread
Thread Starter
Forum
Replies
Last Post
Touge
Canada Forum
3
09-10-2015 08:07 AM
LMURailsplitter02
New Member Forum
1
09-06-2015 10:56 PM
Touge
Canada Forum
0
09-01-2015 10:47 PM
Jazzmeson
RX-8 Parts For Sale/Wanted
0
08-30-2015 02:42 AM