Notices
Series I Do It Yourself Forum Wanna save some coin or time/money in the shop? Read up on Do-It-Yourself custom mods and repairs & post your own here.

DIY: Installing eBay Electronic Throttle Control

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old 09-07-2011, 02:42 AM
  #1  
Registered User
Thread Starter
 
Sergioo915's Avatar
 
Join Date: May 2007
Location: El Paso/Dallas
Posts: 17
Likes: 0
Received 0 Likes on 0 Posts
TX DIY: Installing eBay Electronic Throttle Control

So, looking at some of the post regarding the low idle and vibration issues surrounding RX8, I was wondering if there was a way to control or adjust the position on the throttle butterfly. The idea came from feeling how good and smooth my 8 idles at about 900-950 rpms. My 8 idles pretty good with some vibrations, which can be anoyning. While reving the 8, I noticed it was smooth and nice at about 900-950.
So i found this unit on Ebay for about 110$. It comes from Japan and is all plug and play DIY: Installing eBay Electronic Throttle Control-img_0111_1.jpg

I installed this unit on the radio face plate with very little effort.
DIY: Installing eBay Electronic Throttle Control-img_0140_1.jpg

With double sided tape, I attached the controller box inside the radio unit and guided the wiring throught the channel
DIY: Installing eBay Electronic Throttle Control-img_0136_1.jpg

Plug the harness to the pedal and connect to OBD II port, done.
DIY: Installing eBay Electronic Throttle Control-img_0141_1.jpg

So after programing the unit, I found out that the position on the butterfly connot be ajusted. This unit has preset settings that are NORM, SPORT 1-7 and ECON 1-7.
which I found to be useful in actually changing driving characteristics of the throttle reponse. In Econ mod I got a 1-3 mile per gallon increase. Not bad.
On the Sport Mode, the fuel inconomy sucked, but the responce on the throttle during agrresive turning and accelaration was pretty inpressive. On normal Mode, well its normal. Has a safety feature for while car is in reverse (RED and Yellow wire in the driver running board)
On a lighter note. my car is idleing a little higher. I think its just the nature of the unit reading the data from the CAN bus
DIY: Installing eBay Electronic Throttle Control-photo.jpg
Again, your thoughts and comments.

Last edited by Sergioo915; 09-07-2011 at 02:43 AM. Reason: word
Old 09-07-2011, 04:24 AM
  #2  
Registered
 
oltmann's Avatar
 
Join Date: Sep 2010
Posts: 531
Likes: 0
Received 1 Like on 1 Post
With the Cobb Accessport, you can change the idle speed and the throttle mapping as well as many other things that will improve the performance and reliability of your car. Best bet is to also purchase MazdaManiac's custom calibration service.

http://www.mazdamaniac.com/cobb/accessport.htm

The stock engine computer actually does a great deal to ensure the stability of the idle, but rotary engines simply do not idle well compared to many piston engines. Increasing the idle speed with the AccessPort will improve your idle whilst also properly utilizing the built-in logic in the engine computer which is designed to alter ignition timing and fuel injection to maintain smooth idle.

Simply changing the throttle opening is not sufficient.

Try to return that device if you can.
Old 09-07-2011, 05:15 AM
  #3  
No respecter of malarkey
iTrader: (25)
 
TeamRX8's Avatar
 
Join Date: Apr 2005
Posts: 26,719
Received 2,006 Likes on 1,635 Posts
or just push your throttle foot slower or faster for free ...
Old 09-07-2011, 06:00 AM
  #4  
#50
 
bse50's Avatar
 
Join Date: Nov 2007
Location: Caput Mundi
Posts: 7,521
Received 10 Likes on 10 Posts
Originally Posted by oltmann
With the Cobb Accessport, you can change the idle speed and the throttle mapping as well as many other things that will improve the performance and reliability of your car. Best bet is to also purchase MazdaManiac's custom calibration service.

http://www.mazdamaniac.com/cobb/accessport.htm

The stock engine computer actually does a great deal to ensure the stability of the idle, but rotary engines simply do not idle well compared to many piston engines. Increasing the idle speed with the AccessPort will improve your idle whilst also properly utilizing the built-in logic in the engine computer which is designed to alter ignition timing and fuel injection to maintain smooth idle.

Simply changing the throttle opening is not sufficient.

Try to return that device if you can.
Shhhh, don't tell them.
A resistor like that is one of the stupidest things you can do to a drive by wire car. Like the human brain, some things on our car need some feedback to work properly. Add alcohol and you can't keep a proper erec... well, add this thing and you get my point!
Team is spot on, it does what you can do with your right foot.. only worse.
The MPG is bullshit, it doesn't affect fuelling at all.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
drebbrnator
Series I Trouble Shooting
11
12-27-2018 07:02 PM
rotorocks
Series I Tech Garage
47
05-11-2016 03:23 PM
stickmantijuana
Series I Wheels, Tires, Brakes & Suspension
10
10-27-2015 04:11 PM
MolecularConcept
New Member Forum
15
08-05-2015 04:43 PM
04MazdaMan
Series I Interior, Audio, and Electronics
1
07-15-2015 08:23 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: DIY: Installing eBay Electronic Throttle Control



All times are GMT -5. The time now is 05:28 AM.