RX8Club.com

Notices
Series I Aftermarket Performance Modifications Discussion of power adding modifications

Custom Greddy single ehaust here i go..

     
Old 12-15-2011, 08:15 PM
  #1  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
Custom Greddy single ehaust here i go..
Had just received my muffler for my exhaust 80mm with a 115 mm tip.
sauceyI986 is offline  
Reply Like
Old 12-15-2011, 08:40 PM
  #2  
Registered
iTrader: (13)
 
comebackqid's Avatar
 
Join Date: Mar 2010
Location: California
Posts: 997
Received 19 Likes on 16 Posts
you got some pictures!?
comebackqid is offline  
Reply Like
Old 12-15-2011, 09:22 PM
  #3  
I HATE SPEEDBUMPS!
 
monchie's Avatar
 
Join Date: Nov 2007
Location: Las Vegas, NV
Posts: 8,549
Likes: 0
Received 7 Likes on 6 Posts
Nice. Post some pics please.
monchie is offline  
Reply Like
Old 12-16-2011, 06:32 PM
  #4  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
I will mounted up on friday and post clips right now i just trying figure out on how im going to mount this muffer
Attached Thumbnails Custom Greddy single ehaust here i go..-5a5b2876.jpg  
Last edited by sauceyI986; 12-17-2011 at 06:06 PM.
sauceyI986 is offline  
Reply Like
Old 12-16-2011, 07:56 PM
  #5  
No respecter of malarkey
iTrader: (25)
 
TeamRX8's Avatar
 
Join Date: Apr 2005
Posts: 26,719
Received 2,006 Likes on 1,635 Posts
Originally Posted by sauceyI986
Had just received my muffler for my exhaust 80mm with a 115 mm tip.
You should have also ordered the optional ear plugs to go with it
TeamRX8 is offline  
Reply Like
Old 12-17-2011, 06:11 PM
  #6  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
Lol. Earplugs I know the sound may be different since I had use to run he Greddy Sp2 Exhaust with just a race pipe and like it. I may make some changes all said and done with. But as Iook and compared Greddy makes a deeper sound then the Hks carbon ti.
sauceyI986 is offline  
Reply Like
Old 12-22-2011, 10:20 AM
  #7  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
It will look something like I'm not finish with the rear bumper just yet I will have a carbon diffuser in the rear when all said and done.
Attached Thumbnails Custom Greddy single ehaust here i go..-07a9caf3.jpg   Custom Greddy single ehaust here i go..-9a797c67.jpg  
sauceyI986 is offline  
Reply Like
Old 12-22-2011, 12:16 PM
  #8  
Rotary Rocket
 
Dan507's Avatar
 
Join Date: Oct 2011
Location: England
Posts: 238
Likes: 0
Received 1 Like on 1 Post
Looks good man!
Dan507 is offline  
Reply Like
Old 12-22-2011, 11:19 PM
  #9  
I HATE SPEEDBUMPS!
 
monchie's Avatar
 
Join Date: Nov 2007
Location: Las Vegas, NV
Posts: 8,549
Likes: 0
Received 7 Likes on 6 Posts
You should it have a blue car to match the wheels...lol
monchie is offline  
Reply Like
Old 12-22-2011, 11:40 PM
  #10  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
It well be done to and welded up tommrow afternoon..
sauceyI986 is offline  
Reply Like
Old 12-23-2011, 09:05 AM
  #11  
Registered
iTrader: (5)
 
flametail's Avatar
 
Join Date: Dec 2010
Location: Nashville, TN
Posts: 165
Likes: 0
Received 1 Like on 1 Post
Can't wait to see how it looks, I'm gonna get an A'Pexi N1 and mount it similarly but cut the rear lower bumper like the JIC car.
flametail is offline  
Reply Like
Old 12-23-2011, 10:15 PM
  #12  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
More pics
Attached Thumbnails Custom Greddy single ehaust here i go..-4abfdbef.jpg   Custom Greddy single ehaust here i go..-ad1e3d11.jpg   Custom Greddy single ehaust here i go..-75875353.jpg   Custom Greddy single ehaust here i go..-f0a97225.jpg  
Last edited by sauceyI986; 12-23-2011 at 11:06 PM.
sauceyI986 is offline  
Reply Like
Old 12-23-2011, 11:08 PM
  #13  
Registered
iTrader: (5)
 
flametail's Avatar
 
Join Date: Dec 2010
Location: Nashville, TN
Posts: 165
Likes: 0
Received 1 Like on 1 Post
Love it!
Last edited by flametail; 12-23-2011 at 11:17 PM.
flametail is offline  
Reply Like
Old 12-23-2011, 11:21 PM
  #14  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
Thanks all said and done it set me back about 900
sauceyI986 is offline  
Reply Like
Old 12-23-2011, 11:25 PM
  #15  
Registered
iTrader: (5)
 
flametail's Avatar
 
Join Date: Dec 2010
Location: Nashville, TN
Posts: 165
Likes: 0
Received 1 Like on 1 Post
That include your midpipe, muffler, and cost from the shop to get the pipe bent and installed?
flametail is offline  
Reply Like
Old 12-23-2011, 11:41 PM
  #16  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
The Greddy muffler was $345 special order the midpipe was $200 all the the piping plus resonator was stainless steel came to be about 275 for all the hangers and such was $275 ___total $820 I took a guess.

I have a 3inch all the way back. No sagging or having muffler I have it done up were that is never going to happen
sauceyI986 is offline  
Reply Like
Old 12-24-2011, 12:31 AM
  #17  
Needs Boost!
iTrader: (5)
 
dmedz8's Avatar
 
Join Date: Jul 2010
Location: Lincoln, CA
Posts: 828
Likes: 0
Received 0 Likes on 0 Posts
I like it. are you going to add a diffuser or anything for the edges of the bumper where the shroud used to be?
dmedz8 is offline  
Reply Like
Old 12-24-2011, 12:34 AM
  #18  
Needs Boost!
iTrader: (5)
 
dmedz8's Avatar
 
Join Date: Jul 2010
Location: Lincoln, CA
Posts: 828
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by flametail
Can't wait to see how it looks, I'm gonna get an A'Pexi N1 and mount it similarly but cut the rear lower bumper like the JIC car.
Like this
Name: DSC_6673.jpg Views: 819 Size: 146.8 KB

Name: DSC_4027-1.jpg Views: 1472 Size: 40.3 KB

Name: DSC_4019.jpg Views: 990 Size: 65.5 KB
dmedz8 is offline  
Reply Like
Old 12-24-2011, 12:40 AM
  #19  
Registered
iTrader: (13)
 
comebackqid's Avatar
 
Join Date: Mar 2010
Location: California
Posts: 997
Received 19 Likes on 16 Posts
when you're operational please give us a sound clip, I know vids don't do justice but still wanna hear it. I'm thinking 100+dB LOUD
comebackqid is offline  
Reply Like
Old 12-24-2011, 08:32 AM
  #20  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by dmedz8
I like it. are you going to add a diffuser or anything for the edges of the bumper where the shroud used to be?
Yeah already have another bumper picked out so I add a diffuser under it and make it work.
sauceyI986 is offline  
Reply Like
Old 12-24-2011, 09:47 AM
  #21  
Rotary Rocket
 
Dan507's Avatar
 
Join Date: Oct 2011
Location: England
Posts: 238
Likes: 0
Received 1 Like on 1 Post
Looks great bud. Need a video of how it sounds! :D
Dan507 is offline  
Reply Like
Old 12-24-2011, 10:11 AM
  #22  
Registered
iTrader: (5)
 
flametail's Avatar
 
Join Date: Dec 2010
Location: Nashville, TN
Posts: 165
Likes: 0
Received 1 Like on 1 Post
Originally Posted by dmedz8
Like this
Exactly! I may even have one of the guys I know make me a carbon fiber diffuser that matches the way the JIC one looks after being cut but leave the rotor triangle in the center and get the LED fog put in.
flametail is offline  
Reply Like
Old 12-24-2011, 11:40 AM
  #23  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
Yeah hopefully I will have a video up soon
Right. Now I'm installing a fuel pump and need wire up my engine harness an after that my other oil cooler should be in next week hopefully so I can finally crank this Dam motor
sauceyI986 is offline  
Reply Like
Old 01-22-2012, 09:40 PM
  #24  
Registered
Thread Starter
 
sauceyI986's Avatar
 
Join Date: Jun 2006
Location: Laveen,Az
Posts: 855
Likes: 0
Received 0 Likes on 0 Posts
Ok i know i needed an update but i finally heard the system.. As far as the sound. It sounds deeper and meaner than the Greddy Sp2 Ehaust like it means business there is no more raspyness in the exhaust at all. All i know it was work the money know u people and like to hear and see. so i will get one posted as soon as i get time.
sauceyI986 is offline  
Reply Like
Old 01-22-2012, 10:11 PM
  #25  
Registered
 
Mrktplayer's Avatar
 
Join Date: Apr 2010
Location: Seattle
Posts: 169
Likes: 0
Received 0 Likes on 0 Posts
subscribed...

The exhaust looks great BTW
Mrktplayer is offline  
Reply Like

Thread Tools
Search this Thread
Search this Thread:

Advanced Search
Rate This Thread
Rate This Thread:
You have already rated this thread Rating: Thread Rating: 0 votes, average.
Show Printable Version
Email this Page

Advanced Search
Quick Reply: Custom Greddy single ehaust here i go..


Reply Closed Thread Share

All times are GMT -5. The time now is 05:55 PM.