my 13b rew swap!
 

here is my swap~ much work! but! finally in final steps!
1.engine 13b rew 1995 ported! and repair!
2.turbonetics t76 cold ! 115 hot
3.microtech lt10 with x4
4.walbroo 4oolp fuel pump intank
5.10an fuel lines
6.kgparts fuel rails
7.860cc primary inyectors
8.1600cc bosh secundary inyectors
9.aeromotive 1@1 regulator
10.44mm wastegate
11.turbosmart blow off
12.custom turbo mannifold
13.all oil lines made in braided!
14.battery relocation with 1/0 welded cable in the trunk
15.5speed rx8 transmission compatible with fd3s !
16.1985 3 row radiator
17.ford taurus electric fan! 2 speed
18.MSD COILS!
19.front timimng cover rx7 turbo with ignition!
20.kmr engine mounts!
.........
still to do.
1.trotter cable (accelarotor) installation with gas pedal
2.recondition oem engine rx8 wires ...ELIMINATE ALL NO NEED.
I NEED SOME HELP! I NEED TO know how cables i need to use!
i have crank sensor rx8 for activate eps! but other cables! how much i need!?.
some pics
https://www.dropbox.com/home/rx8%20rew


here is a link for first start up! the engine!
https://www.dropbox.com/s/2if1xymzew...113_171321.mp4

any videos of it running nice swap!

no because i need help for cables of rx8 engine harness! i want to cut unessesary wires! but i dont know how much! i need to eliminate
.i think! i need
1.crank sensor
2.oil pressure
3.air condition
4 temperature
??

I use mechanic metering pump.1987 with timing cover 1987 . I need to know I don't have problems with the OEM rx8 electronic metering pump?

Posted From RX8Club.com Android App

You need the RX8 ECU for EPS, so you will have to keep the CAS in place for that to work.( you can mount it to the front cover, it's been posted before)

The dash works off the RX8 ECU also.

Then you'll need to have the RX8 OMP connected so the RX8 ECU doesn't put the car in into limp mode. (Connect it up and tuck it out of the way somewhere).



G/L bro, looks like your getting closer
.

Λ Yeah but limp mode for what? He's not using the stock tb so it doesn't really matter if it limps or not.

Gotcha, I see he listed it as 1. At the bottom

thanks! ufff! so! i dont need! and temperature and oil pressure work in my dash! fine!
iam closer to start the engine to check leaks! in oil system and fuel system!
very thanks to dznutzuk for tips! help!

here more pics!
the radiator is aluminium! 1985 rx7 ! 3 row! and the electric fan from 1995 ford taurus! jeje! my rx8 is a frankestein! have parts of old cars!

:d:

i did complete 13b rew swap i am running rx8 throttle body

Redrx8rotary : More infos?? Parts used? Pics?

Anybody running PS on any of these swaps??

power steering?

Why wouldn't we be running power steering?

need crank sensor for activate the ps

Im finishing with my 13b re swap. I have it running with a haltech and left the factory ecu for the dash and the electrics stuff. The real question is if im going to be able to get the power stearing to work this way? Or what specificly i need for it to wor? I see you said cas but im using the engines factory one wich is the 24/ 2 tooth type. Is it possible to make it work with that or will i have to change my ignition to maje it work?

you install the rx8 cas to OEM harness to OEM CPU?

I am running the stock electric power steering

Russell29n my ig follow me u will see the setup

red ..what cable u use from the OEM rx8 computer?

Can't see your setup anywhere... :sadwavey:

I have the Cas that comes with the 13b-re engine. Wich is same as the turbo 2 one. I understand you guys are telling me i need the factory cas for the rx8 for the power steering to work. Is it a RPM signal that tells the rack to activate? If thats the case then it could be activated with a tach output from my ECU? What you guys think? I loved too see youre set up redrx but dont have instagram. Looks like using the rx8 timing cover would have been the best way to go but too late for that now. Just want to register and use the car already.

Cano, you have to use the stock rx8 36-2-2-2 trigger wheel with it's mag sensor, no matter what other trigger system you're using to run the aftermarket ecu.

I will try to fit the trigger whell behind my engines pully. The reason i was trying to come up with