Notices
New Member Forum A place for new members to get their feet wet

GURU needed!!

Thread Tools
 
Rate Thread
 
Old Oct 20, 2016 | 03:00 AM
  #1  
H8stock's Avatar
Thread Starter
Registered
 
Joined: Aug 2016
Posts: 35
Likes: 0
GURU needed!!

I need some help guys. I bought an rx8 with the motor out of it, but it was rebuilt. I have the motor in, and it has started and ran 3-4 times for about 5-10 mins. The last time I started it, it idled erratically and kinda choked itself off right before it died. It will crank and crank now, but won't catch. I also noticed when it was running, if I gave it gas, it died. Any ideas? It ran very smooth the first 3 times, sounded great, but the 4th time it choked out.
Reply
Old Oct 20, 2016 | 05:45 AM
  #2  
sonicsdaman's Avatar
The Blue Blur
iTrader: (3)
 
Joined: Apr 2010
Posts: 1,959
Likes: 4,812
From: Green Hill Zone Running in Loops
it could be flooded.
search here or on google for the deflood method
also while your at it look up the break in for rebuilds it might help
Reply
Old Oct 20, 2016 | 06:20 AM
  #3  
H8stock's Avatar
Thread Starter
Registered
 
Joined: Aug 2016
Posts: 35
Likes: 0
I have done the deflood method (removed fuel pump fuse, unhook air pump, crank until it sounds deflooded), it's actually how I got it started a couple times. It doesn't seem to work right now though. I have 1 code for heated o2 sensor, and have reset ecu but no other info. I bought a new maf thinking that might be it...
Reply
Old Oct 20, 2016 | 06:20 AM
  #4  
H8stock's Avatar
Thread Starter
Registered
 
Joined: Aug 2016
Posts: 35
Likes: 0
I also have read and stored the forum posts about break in periods
Reply
Old Oct 20, 2016 | 06:26 AM
  #5  
sonicsdaman's Avatar
The Blue Blur
iTrader: (3)
 
Joined: Apr 2010
Posts: 1,959
Likes: 4,812
From: Green Hill Zone Running in Loops
no real need to pull a fuse, just push the gas peddle down and crank for 10 sec intervals.

also whats the ignition systems health like? brand new?
you didn't give much info to work with
Reply
Old Oct 20, 2016 | 07:54 AM
  #6  
H8stock's Avatar
Thread Starter
Registered
 
Joined: Aug 2016
Posts: 35
Likes: 0
Yeah, I'm sorry about the lack of info. The coil packs, wires, and plugs are all new. There is only one code for a heated oxygen sensor. I haven't done a compression test, but I would like to think that if it starts and runs for awhile (which it did) the compression should be ok. It's a brand new rebuild with the Atkins rebuild kit.
Reply
Old Oct 20, 2016 | 08:18 AM
  #7  
H8stock's Avatar
Thread Starter
Registered
 
Joined: Aug 2016
Posts: 35
Likes: 0
No I have not, i will be sure to do that. Out of curiosity though, if they are improperly hooked up, would it have started and ran like it did? It has ran 4 times for at least 10 mins each time, the last time is choked out and died.
Reply
Old Oct 20, 2016 | 10:04 PM
  #8  
H8stock's Avatar
Thread Starter
Registered
 
Joined: Aug 2016
Posts: 35
Likes: 0
Well thank you for resisting the urge, I am new to this forum, and this platform. But I am not new to research, I understand there are low power injectors, and high power injectors, my question was simply a curious one because the injectors operate at different levels and I wasn't sure if they where swapped around that they would work.

Last edited by H8stock; Oct 20, 2016 at 10:20 PM.
Reply



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -5. The time now is 11:27 AM.