RX8Club.com
a sorry state of affairs for the NC
a sorry state of affairs for the NC
0 2022/06/14 20:34:37
New wheels and a swapped hardtop
New wheels and a swapped hardtop
0 2022/06/14 20:34:36
Got this car running and driving over the winter
Got this car running and driving over the winter
0 2022/06/14 20:34:36
a bit of CAN hacking
a bit of CAN hacking
0 2022/06/14 20:34:35
0 2021/11/21 16:16:34
0 2021/11/21 16:16:33
0 2021/11/21 16:16:31
0 2021/11/08 07:27:51
0 2021/11/08 07:27:51
0 2021/11/08 07:27:50
0 2021/11/03 12:38:38
Also picked up the K&N Typhoon intake. it fits pretty well, but i'm going to have to fabricate the sheet metal for the box as well.
Also picked up the K&N Typhoon intake. it fits pretty well, but i'm going to have to fabricate the sheet metal for the box as well.
0 2021/10/23 10:52:26
Bought a CSF #8066. need to fabricate mounts for it.
Bought a CSF #8066. need to fabricate mounts for it.
0 2021/10/23 10:52:24
I was originally planning on using the oem NC airbox, but i decided it would take too much work, so i mocked up this idea. i'm not a huge fan of pod filters, but if i seal the box and plumb it into the oem rx8 snorkel, it'll be a proper "cold air intake"
I was originally planning on using the oem NC airbox, but i decided it would take too much work, so i mocked up this idea. i'm not a huge fan of pod filters, but if i seal the box and plumb it into the oem rx8 snorkel, it'll be a proper "cold air intake"
0 2021/10/18 07:04:51
The rx8 engine harness doesn't reach the NC ecu location, so i'll need to make or buy an extension harness
The rx8 engine harness doesn't reach the NC ecu location, so i'll need to make or buy an extension harness
0 2021/10/18 07:04:44
Found a spot for the electric power steering module. will need a bracket of course.
Found a spot for the electric power steering module. will need a bracket of course.
0 2021/10/18 07:04:43
Fuel Pump wiring page out of my FSM
Fuel Pump wiring page out of my FSM
0 2021/10/05 16:30:00
running the rx8 ECU in the stock NC location
running the rx8 ECU in the stock NC location
0 2021/10/04 19:23:15
the rx8 fresh air tube fit with a bit of trimming. The NC airbox lines right up with it
the rx8 fresh air tube fit with a bit of trimming. The NC airbox lines right up with it
0 2021/10/04 19:23:14
loaded all the components into the engine bay to pretend it's done
loaded all the components into the engine bay to pretend it's done
0 2021/10/04 19:23:14
going to need to fabricate a bracket to mount the air pump over here
going to need to fabricate a bracket to mount the air pump over here
0 2021/10/04 19:23:13
threw all the major components together to see how everything felt. if i didn't know better, i'd say it was meant to be here.
threw all the major components together to see how everything felt. if i didn't know better, i'd say it was meant to be here.
0 2021/09/26 11:58:03
here's an angle of it inside the miata
here's an angle of it inside the miata
0 2021/09/26 11:58:02
looked at my spare trans. dunno how i never noticed this, but the shifter has a kick to the side.
looked at my spare trans. dunno how i never noticed this, but the shifter has a kick to the side.
0 2021/09/26 11:58:02
Loaded the engine and subframe up into the car
Loaded the engine and subframe up into the car
0 2021/09/25 13:20:02
also started draping the wiring harnesses all together. This is going to take forever.
also started draping the wiring harnesses all together. This is going to take forever.
0 2021/09/25 13:20:01
not exactly sure why it seems to be so far to the left in this picture. the turret is slightly bound on the hole itself, so it's possible when i make the hole bigger, it will center itself in that dimension.
not exactly sure why it seems to be so far to the left in this picture. the turret is slightly bound on the hole itself, so it's possible when i make the hole bigger, it will center itself in that dimension.
0 2021/09/25 13:20:01
checking fitment. the shifter hole needs to be made slightly wider.
checking fitment. the shifter hole needs to be made slightly wider.
0 2021/09/25 13:20:01
0 2021/09/25 13:20:00
NC Driveshaft fits
NC Driveshaft fits
0 2021/09/25 13:20:00
Exhaust is kinda close to the side of the tunnel here. it's not touching anything currently, but it's pretty close and i don't really want it catching on fire. I'll likely bash the sides in a little bit for got luck.
Exhaust is kinda close to the side of the tunnel here. it's not touching anything currently, but it's pretty close and i don't really want it catching on fire. I'll likely bash the sides in a little bit for got luck.
0 2021/09/25 13:19:59
I used two NC PPF bolts backed up into either other
I used two NC PPF bolts backed up into either other
0 2021/09/13 17:25:01
These studs need to come out of the PPF.
These studs need to come out of the PPF.
0 2021/09/13 17:25:00
fully assembled dry run of the RX8 transmission and differential with an NC PPF and driveshaft
fully assembled dry run of the RX8 transmission and differential with an NC PPF and driveshaft
0 2021/09/13 17:21:42
this shows the spacer required to fit the NC ppf to the rx8 diff
this shows the spacer required to fit the NC ppf to the rx8 diff
0 2021/09/13 17:21:42
0 2021/09/13 17:21:41
NC ppf on the rx8 diff
NC ppf on the rx8 diff
0 2021/09/13 17:21:41
simple spacer for the rx8 diff
simple spacer for the rx8 diff
0 2021/09/13 17:21:40
cluster and dash also needed a bit of trimming, but this fit right together.
cluster and dash also needed a bit of trimming, but this fit right together.
0 2021/09/04 15:45:24
NC steering column (left) Rx8 Column (right)
NC steering column (left) Rx8 Column (right)
0 2021/09/04 15:45:24