RX8Club.com
Turning onto highway near Franz Joseph
Turning onto highway near Franz Joseph
0 2022/11/04 21:54:44
Lake Ianthe
Lake Ianthe
0 2022/11/04 21:54:35
Nelson Lakes
Nelson Lakes
0 2022/11/04 21:54:23
Surrounded on the Cook Straight ferry
Surrounded on the Cook Straight ferry
0 2022/11/04 21:54:13
Woolshed outside Foxton
Woolshed outside Foxton
0 2022/11/04 21:54:04
0 2022/10/24 00:26:19
Best match up of the day .... very close finish but lost by a bumper.
Best match up of the day .... very close finish but lost by a bumper.
0 2022/10/24 00:26:10
0 2022/10/23 01:15:13
0 2022/10/22 22:14:31
0 2022/10/22 22:14:25
0 2022/10/22 22:14:21
0 2022/10/22 22:14:15
0 2022/10/22 22:14:09
0 2022/10/22 22:14:02
Something to get Team excited !
Something to get Team excited !
0 2022/10/17 20:52:50
2nd to 8000 3rd to 7500
2nd to 8000 3rd to 7500
0 2022/10/14 22:50:05
0 2022/10/09 12:32:32
Onto the billet ...........
Onto the billet ...........
0 2022/09/23 01:42:45
0 2022/09/13 13:40:08
0 2022/08/21 20:20:33
0 2022/08/21 20:20:13
0 2022/07/18 19:54:06
2nd and 3rd with 7000 boost cut
2nd and 3rd with 7000 boost cut
0 2022/07/18 19:53:18
2nd and 3rd ...no boost cut
2nd and 3rd ...no boost cut
0 2022/07/18 19:52:28
First batch .....GONE !
First batch .....GONE !
0 2022/05/23 16:46:28
0 2022/05/18 19:32:55
0 2022/05/18 19:32:19
0 2022/05/15 22:12:40
Finally ! First batch ready for machining ......
Finally ! First batch ready for machining ......
0 2022/02/27 18:52:51
Fitting would go approx where black cross is.
Fitting would go approx where black cross is.
0 2022/02/07 11:18:57
Showing room under turbo for wastegate pipe
Showing room under turbo for wastegate pipe
0 2022/02/07 11:18:50
0 2022/02/03 00:15:25
0 2022/02/03 00:12:52
First three cast manifolds . Top one fitted the gtx2582r and is going to a local here in NZ. Next one down is the one On my current setup. Bottom one went to Aussie and is currently being fitted.
First three cast manifolds . Top one fitted the gtx2582r and is going to a local here in NZ. Next one down is the one On my current setup. Bottom one went to Aussie and is currently being fitted.
0 2022/01/29 17:17:47
This was the dyno for G30-660 with the 1.01AR turbine. With the 0.83 it comes on 4-500rpm earlier than this with minimal drop in whp up top.
This was the dyno for G30-660 with the 1.01AR turbine. With the 0.83 it comes on 4-500rpm earlier than this with minimal drop in whp up top.
0 2022/01/29 17:11:55
Getting the brackets done .
Getting the brackets done .
0 2022/01/22 16:06:05
0 2022/01/08 14:57:49
0 2021/12/29 15:27:24
0 2021/12/29 15:26:53
from rear looking fortward
from rear looking fortward
0 2021/12/29 15:18:06