RX8Club.com
0 2021/10/02 21:49:38
0 2021/10/11 15:32:30
0 2021/10/19 18:52:27
0 2021/10/22 08:22:50
New rubber , new radiator , new battery .... any excuse for some more stratos blue majic.
New rubber , new radiator , new battery .... any excuse for some more stratos blue majic.
0 2021/10/24 12:46:45
0 2021/10/24 15:57:41
0 2021/10/24 18:03:51
0 2021/12/14 11:43:18
0 2021/12/15 14:34:55
0 2021/12/19 10:58:11
0 2021/12/20 16:59:06
0 2021/12/20 23:29:45
0 2021/12/20 23:52:00
0 2021/12/24 01:42:21
0 2021/12/29 10:30:31
Took some effort but got there eventually. Wheel well seems cooler after this extra shielding
Took some effort but got there eventually. Wheel well seems cooler after this extra shielding
0 2021/12/29 15:17:45
Manifold also shielded ... for heat management .
Manifold also shielded ... for heat management .
0 2021/12/29 15:17:50
Turbo in wheel well before exit coupler fitted
Turbo in wheel well before exit coupler fitted
0 2021/12/29 15:17:54
Underneath showing how tight it is before WG piope fitted.
Underneath showing how tight it is before WG piope fitted.
0 2021/12/29 15:18:00
from rear looking fortward
from rear looking fortward
0 2021/12/29 15:18:06
0 2021/12/29 15:26:53
0 2021/12/29 15:27:24
0 2022/01/08 14:57:49
Getting the brackets done .
Getting the brackets done .
0 2022/01/22 16:06:05
This was the dyno for G30-660 with the 1.01AR turbine. With the 0.83 it comes on 4-500rpm earlier than this with minimal drop in whp up top.
This was the dyno for G30-660 with the 1.01AR turbine. With the 0.83 it comes on 4-500rpm earlier than this with minimal drop in whp up top.
0 2022/01/29 17:11:55
First three cast manifolds . Top one fitted the gtx2582r and is going to a local here in NZ. Next one down is the one On my current setup. Bottom one went to Aussie and is currently being fitted.
First three cast manifolds . Top one fitted the gtx2582r and is going to a local here in NZ. Next one down is the one On my current setup. Bottom one went to Aussie and is currently being fitted.
0 2022/01/29 17:17:47
0 2022/02/03 00:12:52
0 2022/02/03 00:15:25
Showing room under turbo for wastegate pipe
Showing room under turbo for wastegate pipe
0 2022/02/07 11:18:50
Fitting would go approx where black cross is.
Fitting would go approx where black cross is.
0 2022/02/07 11:18:57
Finally ! First batch ready for machining ......
Finally ! First batch ready for machining ......
0 2022/02/27 18:52:51
0 2022/05/15 22:12:40
0 2022/05/18 19:32:19
0 2022/05/18 19:32:55
First batch .....GONE !
First batch .....GONE !
0 2022/05/23 16:46:28
2nd and 3rd ...no boost cut
2nd and 3rd ...no boost cut
0 2022/07/18 19:52:28
2nd and 3rd with 7000 boost cut
2nd and 3rd with 7000 boost cut
0 2022/07/18 19:53:18
0 2022/07/18 19:54:06
0 2022/08/21 20:20:13
0 2022/08/21 20:20:33