RX8Club.com
0 2020/11/03 21:14:25
0 2020/11/03 21:24:06
0 2020/11/03 21:34:13
0 2020/11/03 21:35:15
0 2020/11/03 21:36:52
This is roughly what the sludge inside the engine would look like.
This is roughly what the sludge inside the engine would look like.
0 2020/11/03 22:04:27
This is roughly what looking into your coolant cap would look like.
This is roughly what looking into your coolant cap would look like.
0 2020/11/03 22:04:32
0 2020/11/03 22:08:27
0 2020/11/03 23:06:04
JDM 4port flywheel (left) US 6 port flywheel (right)
JDM 4port flywheel (left) US 6 port flywheel (right)
0 2020/12/02 21:42:16
0 2020/12/02 21:42:31
0 2020/12/02 21:46:58
0 2020/12/12 20:54:45
0 2020/12/02 21:48:32
0 2020/12/21 15:02:23
0 2020/12/24 18:44:07
0 2021/01/01 16:14:32
Rx8 vs T2 Centerplate
Rx8 vs T2 Centerplate
0 2021/01/07 19:17:31
0 2021/03/16 19:23:39
0 2021/04/19 20:18:28
0 2021/04/20 14:57:25
0 2021/04/20 15:00:18
0 2021/11/15 07:40:01
0 2021/11/15 10:22:06
0 2023/07/25 15:21:59
0 2023/07/27 10:53:45
0 2023/07/29 06:45:27
Modified the CX mount to fit the nicon pan. This allowed us to get the engine finally in place and centered.
Modified the CX mount to fit the nicon pan. This allowed us to get the engine finally in place and centered.
0 2023/09/03 16:00:58
Engine and trans had to slide back to match the stock location on the PPF.
Engine and trans had to slide back to match the stock location on the PPF.
0 2023/09/03 16:02:46
Picked up some JIS fasteners to start replacing old crusty ones.
Picked up some JIS fasteners to start replacing old crusty ones.
0 2023/09/03 16:03:07
Found my rear iron belhousing cover on a shelf from the REN and it seems to bolt right in.
Found my rear iron belhousing cover on a shelf from the REN and it seems to bolt right in.
0 2023/09/03 16:03:24
Also persuaded the firewall a little bit to fit the new LIM positioning......youd think if CX made a mount brace and a LIM swap kit that you wouldnt be rubbing on the firewall.
Also persuaded the firewall a little bit to fit the new LIM positioning......youd think if CX made a mount brace and a LIM swap kit that you wouldnt be rubbing on the firewall.
0 2023/09/03 16:03:37
0 2023/11/08 15:53:17
0 2023/11/08 15:54:11
0 2023/11/08 15:54:32
0 2023/11/08 15:55:09
0 2023/11/08 16:02:05
0 2023/11/08 16:03:59
0 2023/11/08 16:29:01
0 2023/11/08 16:34:11