Rich - emailed you a few times about the replacement pin to get rid of the rattle, not sure if you received my emails. Can you get one of those out to me? Let me know if I need to email you separately again.

PCS

 

All the ones I had names for are mailed out.
Give me your zip and I'll tell you.

 

91006 - I was the one who came out for the test fit in the blue rx8

 

I still need a name and address to ship to.
I tried putting PCS on the package but the PO wouldn't take it.
They want an address.

 

Received parts today




Will try to install and report back tomorrow

 

ATT. All the S2.2 shifters mailed out last week have to come back.
There was a mistake in the program and the shoulder is to high to allow reverse.
If you got one don't install it just turn it around.
**** happens

 

I need another test car, pcs can't make it out here.
We can't ship anymore shifters until we try one out.
email rap@axialflow.com

 

RP,

Does that mean that we shouldn't bother installing the recently shipped replacement parts? Or are those OK?

Please advise, thanks!

 

Go ahead and use them. The problem we are having right now is with thhe currant batch. Here we had a program problem.
I'm still trying to get a test car for this.

 

Any update? I ordered mine in May.

 

You should have it. But your forum name dosn't tell me who you are.
Send me an email to: rap@axialflow.com

 

Got mine today, my zip is 11572. I'm assuming this is a 2.2. Did not receive any instructions or dowel, but will attempt install from Paimons website.

Thanks,

-FG

 

You do not need dowels or spacer plate with the S2.2 it's a drop in just like S1 was.

 

I just installed the shifter and my first impression was that sliding into first gear, in other words front left corner is not so easy. I kind of have to go a little to the right to find first. Did I do something wrong? The pros so far are that the shifts from second to third are much more smoother. The movement of the shifter is also very rigid.

 

I think you'll get used to that, to the point of not noticing it. It's just that the throw is shorter sideways also and it doesn't hit the side wall.
I do need to ask you if the reverse lock out is working.
We had trouble with one unit and I want to know if it's just that one.
Could you email me direct at: rap@axialflow.com

RAP

 

I hope I got all the orders filled.
That done then there are 2 left on the shelf.
S1's are going out and there are some left over but I don't know haw many yet.

Thanks to all of you,
Richard

 

We solved the lockout problem. Which also made the shift into first easier.
Now there is only one left.

 

hey Richard, I sent you a pm on the 17th. Checking to see if you still have the one or not.

 

Just checked and yes it's still here.

 

thanks! I'll send payment once you confirm if you want me to send directly through PayPal or your website. Would you be able to ship tomorrow? Ship date will determine which shipping address I'll put down.

 

Pay however you like. If you buy now it will go out tomorrow at noon. Via Priority Mail which takes 2-3 days. If you're near a major city it will take 2 otherwise 3.
RAP

 

Hi Richard, I've sent you several emails regarding the replacement parts from the first batch of shifters sent out. I haven't received any updated parts or correspondence from you either. Can you tell me if you're getting my emails. Regards
Jared

 

Richard, I believe I purchased the last one from the most recent batch. I'm not so certain mine had the new parts mentioned in page 9 since the vibration is quite audible above 2k RPM. I'll be local to you in 1.5 weeks. Are you free the week of the 18th for me to stop by?

 

I've got a new part designed for the upper bearing. It will not be ready for about two weeks. It will be free to anyone who is having a problem.
Hopefully it will work that is.

 

It never hurts to have another car to try things out on. Juat call first.