RX8Club.com

RX8Club.com (https://www.rx8club.com/)
-   Series II Exterior Appearance and Body Kits (https://www.rx8club.com/series-ii-exterior-appearance-body-kits-166/)
-   -   HID headlights in non-HID equipped car? (https://www.rx8club.com/series-ii-exterior-appearance-body-kits-166/hid-headlights-non-hid-equipped-car-264338/)

moldyviolinist 01-13-2017 09:59 AM

HID headlights in non-HID equipped car?
 
If I buy the OEM HID headlight assembly, is it direct plug and play with my 2009 Sport which does NOT have HIDs?

Would quite like to upgrade the lights on my car, but not sure if it'll fit? Don't want to use aftermarket HID conversion as I know those will probably blind oncoming cars.

Thanks

NotAPreppie 01-13-2017 11:29 AM

You'll also need the supporting electronics (ballasts/igniters).

moldyviolinist 01-13-2017 01:36 PM

OK yes of course. But it will be plug and play?

Also, does anyone know the part numbers for the ballasts and igniters? I can only seem to find a "hid control module"?

NotAPreppie 01-13-2017 06:13 PM

I don't have the answers but here is where I would start if I were looking.
2009 Mazda RX-8 HEAD LAMPS

Staf00 12-26-2022 11:01 PM

Bump. I'd like to know the answer to this as well...ty!

Fickert 12-27-2022 09:01 AM


Originally Posted by Staf00 (Post 4977034)
Bump. I'd like to know the answer to this as well...ty!

I did this in the past. If I remember I will check my harness. Its out of the car currently.

Staf00 01-01-2023 11:06 AM

Fickert, were you able to check your harness by any chance?

Fickert 01-04-2023 09:39 AM


Originally Posted by Staf00 (Post 4977285)
Fickert, were you able to check your harness by any chance?

Hey sorry I just looked at this last night actually. Hold up, I can get you information later today, if not tonight when I get home.

Fickert 01-04-2023 05:33 PM

@Staf00

Pinout below:

LH Headlight:
OEM Harness -> HID Connector
LGrn/BLk -> LGrn/Blk
Blk -> Blk/Y
Brn -> Brn
Vio/Wht -> Vio/Wht

RH Headlight:
OEM Harness -> HID Connector
LGrn/Blk -> LGrn/Blk
Blk -> Blk/Y
Brn -> Brn
Wht/Blk -> Wht/Blk

If you have question, let me know! I will say I know for certain the LH is correct, I had to guess a bit on the RH but I am pretty sure its correct so do the drivers first, and pay attention to which wires go where. Pin location wise it is the same on the passenger side. Also you will have 3 left over wires in the HID Harness you will not use. Just trim them short.

For safety I suggest putting in a 5amp fuse for the LH and RH headlight circuit. It should just be under 5 amps on startup. This way if you have a wiring issue it can blow the fuse first and save a ballast.

Good luck!

etikoner 04-27-2023 07:10 AM

Bump, I received JDM HID headlights for S2 RX-8 and the harnesses are completely different.

tried to make a post in the classifieds searching for a chassis side HId headlight harness but I wasn’t allowed.

anyone have one I can purchase?

thanks!


All times are GMT -5. The time now is 02:23 PM.


© 2024 MH Sub I, LLC dba Internet Brands