RX8Club.com

RX8Club.com (https://www.rx8club.com/)
-   Series I Tech Garage (https://www.rx8club.com/series-i-tech-garage-22/)
-   -   Dyno Results w hard data (On a known Dynojet) (https://www.rx8club.com/series-i-tech-garage-22/dyno-results-w-hard-data-known-dynojet-7863/)

jmanolov 09-18-2003 03:04 AM

Ok, you say it may turn out the car can not be measured at the dyno because the ECU retards smth knowing it is not moving.

What about a GTechPro Competition? :)
The car is moving in real world, and the GTechPro Comp is a quite accurate device. Or you say the RX-8 smart ECU even detects our thoughts about attaching g-meters to the car and hides the horsepower just like on a dyno.

I can't say more but check an upcoming issue of Sport Compact Car related to GTech and RX-8 :P

Magic8 09-18-2003 06:06 AM

Has anyone seen Paul Yaw's post on his experiences with dynoing the RX-8 engine. He said that the onboard computer is really giving him a hard time. Apparently the ECU does strange things if it doesn't detect front wheels moving.

Anyways here is his post.
http://www.rx8forum.com/showthread.php?threadid=10823


There was another thread that had Japanese dyno results. 217ps at the wheels, 180 ps when its at 6200, and max torque of 20.1kg-m at 6370.
http://www.rx8forum.com/showthread.php?threadid=11170



Magic8

compaddict 09-18-2003 08:45 AM

Saw the posts and the thing I find interesting is that the Japan dyno test doesn't seem to have a problem with the computer.
On the other side we really don't have any information on the test so maybe they did something to compensate.

Vince

canzoomer 09-18-2003 10:26 AM

Sorry, I missed that statement about the ECU or car detecting if the front wheels are moving or not.
Who made it?

There is no sensor to the front wheels that would be needed to detect this.

Look at the wiring diagrams to verify this.
I just did.

There IS a brake sensor, but it only engages when the brakes are on.

Gord96BRG 09-18-2003 11:18 AM


Originally posted by canzoomer
Sorry, I missed that statement about the ECU or car detecting if the front wheels are moving or not.
Who made it?

It was Paul Yaw, in the thread referenced above ( this one ). He said:

This is a hard car to understand.

A bare motor on the dyno with aftermarket fuel injection is sensible enough, but the factory computer makes anything power related quite challenging.

I will probably get a big flame war started with this one, but this car will not dyno properly without the front wheels spinning. I spent an evening scouring the service manual, and there are pages of error codes caused by anything from a sensor reading being out of range, to a forced power reduction mode based on calculated catalytic converter core temperature.

This car is a rolling computer, and it is not thrilled with full throttle high rpm operation while sitting still.

The air fuel ratio will be rich, and the timing will be retarded. It's kind of like removing the speedometer cable from your TII. The car goes nasty rich and doesn't make any power.

It's so bad that I have dusted off my old in car dyno to use for development. It is a real pain to use compared to a chassis dyno, but at least the results will be accurate.

(I will probably have to amortise the cost of speeding tickets into the parts price!)

I don't want to be designing an intake system that increases power because it leans the mixture on the dyno, only to find that there is a power loss once the car is rolling and the air fuel ratio goes too lean.

The idea of running it on the engine dyno with the stock computer is not even an option.

As a result of all this complexity, and the cars bad attitude on a chassis dyno, I will need to outfit it with some data acquisition, and the in car dyno to make sense of the results.
I was reading your other posts about investigating the ECU - interesting work, canzoomer. I appreciate your efforts toward understanding the RX-8 systems!

Regards,
Gordon

miztic 09-18-2003 12:21 PM

there would HAVE to be a wheelspin sensor on every wheel, its used for ABS (to see if the wheels are locked up) and I bet it is used for the DSC/TCS systems, so it can figure out which wheel to apply brakes to... maybe you're looking at the wrong wiring diagram canzoomer ?

bern 09-18-2003 01:52 PM


...to a forced power reduction mode based on calculated catalytic converter core temperature....
In here lies the whole mystery to the, emmissions related, USA ECU re-calibration issue.



there would HAVE to be a wheelspin sensor on every wheel, its used for ABS (to see if the wheels are locked up) and I bet it is used for the DSC/TCS systems, so it can figure out which wheel to apply brakes to...
This is a correct assumption. The ECU does use the ABS sensors in this role.


Based on research we gathered at Mazda and information from folks like Paul Yaw (which mentioned his research to me a few days ago), we did know that the 8 potentially defaults with up to 3 protection codes while on a dyno.

DISCLAIMER: I will not claim to know, how much exactly this protection mode effects performance #'s on a dyno, only that it does. The % is what is not known at this time.

-Bern

btw, no one has to believe me if they don't want, it's ok.

rotarynews.com 09-18-2003 03:51 PM

Off my chest!
 
Since thigs are out in the open now, I won't have to explain this to a thousand people at SevenStock. I guess we should have just play the 20 questions game from the start.

To reiterate: 3 know faults on the Dyno cause the car to go into Safe Mode. This is not a guess, it is a fact, and can be verified by someone with a code reader (how's that project coming along, anyhow?). You can also verify this by seeing the upper end of the dyno "spazz out" ... and look at the AF readings.

Now as to the why on the power reduction: Cat Core temp... By federal law, emmission equipment has to last for 100,000 miles. At the rotary's high exhaust temperature, the cat will destroy itself. (any previous RX-7 owner can tell you cheap cats will be destroyed by the rotary's hot-hot-hot exhaust in a matter of months... causing a neato flaming/shooting of little peices of converter material out the tail pipes... Happend on both my 1st gen (12a) and 2nd gen (13b) )

So there is hope: The engine is able to produce the orig promised HP, at the cost of cat longevity. Or, if anyone know a good chemical engineer with specialization in thermal calalistic reactions, have them see if there is anything they can recommed for a long-life, high-flow cat that can last under the extreme heat of a rotary's exhaust.



And to the Mazda folks who we promised not to reveal the causes( that read this forum), we are simply restating what someone else on the forum has mentioned.

Speed Racer 09-18-2003 03:57 PM

Finally some real confirmation of what is happening with the odd dyno results. I wonder why Mazda couldn't come out and just say that the car goes into "safe mode" when it is dynoed? It would have saved a lot of us a ton of frustration.

Broker73 09-18-2003 04:00 PM

Thanks
 
thanks for the good work, maybe now we will put to rest the Dyno guys on here that have been crying about HP...........

Magic8 09-18-2003 04:12 PM

newb question

It's running rich, so that the excess hydrocarbon will "cool" the catalytic converter to meet the operational life requirement. Is that why it runs so rich?


Magic8

rotarynews.com 09-18-2003 04:14 PM


Originally posted by Speed Racer
Finally some real confirmation of what is happening with the odd dyno results. I wonder why Mazda couldn't come out and just say that the car goes into "safe mode" when it is dynoed? It would have saved a lot of us a ton of frustration.
No kidding! We would have loved to give out this information when we first go it.. I'm sure Mazda has a good reason for asking us to keep quiet about it...

How about speculation for the reason they didn't want us to release the information :D

zoom44 09-18-2003 04:22 PM

thank you paul yaw, dan and bern!!

RodimusOne 09-18-2003 06:57 PM

Thanks for the update!

So does this explain why for the first few thousand miles or so, we're saying really low mpg due to the cat. issue?

downshift 09-18-2003 07:04 PM

Phew!

Finally something substantial. I'm deliberating on getting one and this is interesting news indeed. However, I'm a little confused here. I thought the lowered HP was due to last minute changes in emissions. Is the 'too hot for the cat' issue behind the official claimed emissions issue? So can I assume the cats' on the JDM version of the RX-8 is going to go out sooner since their power is not reduced and they don't have that federal emissions rule?

Any word on the low MPG seen by some people or is this still shrouded in secrecy because Paul Yaw haven't figured it out yet? :D

RodimusOne 09-18-2003 07:26 PM

Well, here's my uneducated 2 cents...

Can anyone validate if these assumptions are feasible enough for us to put rest the hp/mpg issue(s):

1. Mazda engineers reprogrammed the ECU (to lower hp) on all the cars at port during that few weeks to comply to ensure the cat converter survives the federal emission law 100k mi requirements.

2. At the same time, to ensure longetivity of the cat converter, the ECU was programmed to allow only 'rich' burning of the fuel in the engine so that the excess hydrocarbon will 'burn-in' the cat converter slowly (therefore slowly getting use to excess heat generated by the renesis engine). This is why we are getting low mpgs in the first few thousand miles of driving the car.

3. In the future, the 2005 model will probably include a higher quality cat converter capable of withstanding all the excess heat the renesis is generating, and will provide the stated mpg right of the bat.

Do you think these assumptions are valid?

rotarynews.com 09-18-2003 07:30 PM

I can tell you about the gas issue from my own experience... WE ARE LEAD FOOTS! I'm had PB injected into my foot when I was 16. I love to have the engine rev... floor it to redline through 1st and 2nd on almost every traffic light. I was seeing 14.8 or so MPG.
Then I started driving like a granny... shifting before 3500, using cruise on the freeway, obeying all speed limits... 18 MPG.

On a trip from LA to Las Vegas, in 120F heat, with the AC on, cruise set around 80-85, 22MPG from Victorville to a gas station in the southern end of the valley.

We'll see how well I do next fill up, and from Vegas to SoCal for SevenStock!

mikeb 09-18-2003 08:02 PM

cool
see ya in irvine

bureau13 09-18-2003 08:22 PM

Re: Off my chest!
 
OK, this could explain a lot of things...but I have a couple related questions. First...why the comments that they probably would not be adding a turbo to the Renesis because it would be difficult getting the cats up to operating temps? Hell...sounds like adding a turbo would fix some of their problems :-) (Those comments may not have come from Mazda...for some reason I thought they did).

Second...several people have posted G-Tech "dyno charts" that appear to match the torque characteristics of the chassis dynos. I doubt the G-Tech tests were causing the car to enter any kind of safe mode...why wouldn't they show a nice flat torque curve in the upper revs?

jds


Originally posted by rotarynews.com
Since thigs are out in the open now, I won't have to explain this to a thousand people at SevenStock. I guess we should have just play the 20 questions game from the start.

To reiterate: 3 know faults on the Dyno cause the car to go into Safe Mode. This is not a guess, it is a fact, and can be verified by someone with a code reader (how's that project coming along, anyhow?). You can also verify this by seeing the upper end of the dyno "spazz out" ... and look at the AF readings.

Now as to the why on the power reduction: Cat Core temp... By federal law, emmission equipment has to last for 100,000 miles. At the rotary's high exhaust temperature, the cat will destroy itself. (any previous RX-7 owner can tell you cheap cats will be destroyed by the rotary's hot-hot-hot exhaust in a matter of months... causing a neato flaming/shooting of little peices of converter material out the tail pipes... Happend on both my 1st gen (12a) and 2nd gen (13b) )

So there is hope: The engine is able to produce the orig promised HP, at the cost of cat longevity. Or, if anyone know a good chemical engineer with specialization in thermal calalistic reactions, have them see if there is anything they can recommed for a long-life, high-flow cat that can last under the extreme heat of a rotary's exhaust.



And to the Mazda folks who we promised not to reveal the causes( that read this forum), we are simply restating what someone else on the forum has mentioned.


RodsterinFL 09-18-2003 08:26 PM

Late Haikus

Dyno dunno why;
Still loving my RX8;
It is so much fun.

glad to hear the news;
waiting to hear some more stuff;
yes I want the truth.

canzoomer 09-18-2003 08:47 PM


Originally posted by miztic
there would HAVE to be a wheelspin sensor on every wheel, its used for ABS (to see if the wheels are locked up) and I bet it is used for the DSC/TCS systems, so it can figure out which wheel to apply brakes to... maybe you're looking at the wrong wiring diagram canzoomer ?
Not when the DSC is disabled.
Then the sensors are out of circuit. They are UNPOWERED in this state.
The circuit is clearly marked on the diagrams.

I know, we hooked a meter to them. No voltage, no current, no signal.

ALL the dyno runs we have seen come from people who claim they turned off the DSC.

bern 09-18-2003 08:59 PM

Re: Re: Off my chest!
 

Originally posted by bureau13
OK, this could explain a lot of things...but I have a couple related questions. First...why the comments that they probably would not be adding a turbo to the Renesis because it would be difficult getting the cats up to operating temps? Hell...sounds like adding a turbo would fix some of their problems :-) (Those comments may not have come from Mazda...for some reason I thought they did).
The turbo temp issue is a "cold" start related problem. On the other side of the spectrum. It would not allow the cat to fire off quick enough to meet emission requirements, and maybe, rob too much heat from the cat during normal engine operation!! It seems like we can't win. What we need is, a super-duper Rotary only cat! ;)

-Bern

canzoomer 09-18-2003 09:05 PM

Re: Off my chest!
 

Originally posted by rotarynews.com

So there is hope: The engine is able to produce the orig promised HP, at the cost of cat longevity. Or, if anyone know a good chemical engineer with specialization in thermal calalistic reactions, have them see if there is anything they can recommed for a long-life, high-flow cat that can last under the extreme heat of a rotary's exhaust.



And to the Mazda folks who we promised not to reveal the causes( that read this forum), we are simply restating what someone else on the forum has mentioned.

Umm, so why are the catalytic converters in Japan not at risk of melting down??

I am not arguing what you said about cats. Get em too hot and they can cook.
Some makers now do dual cats, a Rhodium catalyst pre-cat, which can take high heat, right by the exhaust manifold, and a secondary ( Palladium catalyst I believe) further back where it is cooler.

Another big risk with a too-rich mixture is backfiring, where unburned fuel detonates in the exhaust right after the exhasut ports. The shock waves can shatter the catalyst bricks.

This happened to Nissan with the Altima and Sentra SE-R Spec V.
They have a massive recall on the Spec V and the Altima right now to inspect, replace cats, re-calibrate the ECU, and replace engines as needed. The shattered cats released small bits which got sucked up into the engines via the exhaust valves.
About 1 in 3 cars inspectedin the recall are getting new engines, I hear.

I used to own one, so I have been watching this with interest.
Fortunately I changed the entire exhasut system on mine at 3200km, and put in a Stillen header, and a Vibrant cat way further back down the pipe. Met Canada emissions regs, but would never have passsed in California. I used to hear the backfiring all the time on decelleration. Classic stupid use of too-rich conditions to make the cats work "better" at the detriment of the performance economy and parts life.

Oh, and cats use more fuel to make more heat, to do their jobs.
This is a problem as it makes more heat and nitrous oxide coming from the exhaust.
How big a problem?
The EPA says it is contributing to global warming in a major way.
See:
http://media.fastclick.net/w/get.med...atalyt.htm&d=f

canzoomer 09-18-2003 09:13 PM

Re: Re: Re: Off my chest!
 

Originally posted by bern


The turbo temp issue is a "cold" start related problem. On the other side of the spectrum. It would not allow the cat to fire off quick enough to meet emission requirements, and maybe, rob too much heat from the cat during normal engine operation!! It seems like we can't win. What we need is, a super-duper Rotary only cat! ;)

-Bern

Maybe. I doubt we can add much boost to the Renesis.
It is what, 10:1 compression ratio?
Add too much boost and you create a knock condition.

The earlier turbo'ed RX-7's use a much lower compression ratio.

bern 09-18-2003 09:14 PM

Re: Re: Off my chest!
 

Originally posted by canzoomer
....Umm, so why are the catalytic converters in Japan not at risk of melting down??...
They are not per se' in risk of melting down, but I do bet they don't have to last the US federal emissions mandated 100K miles. I think Mazda was forced to play it safe with RX-8 here.

Longevity is the key thought here.

-Bern


All times are GMT -5. The time now is 06:08 AM.


© 2024 MH Sub I, LLC dba Internet Brands