My new Turbo install project.
Here is a pic of the manifold in pieces, turbo flange, turbo blanket, and a turbo. I forgot which one this is. Its not for my application. I'm using a T4 60 trim which has the same size of compressor housing as the 3071r
This will be a custom topmount. Battery will have to be relocated into the trunk and the AST will be Aluminium. Specs of the selected turbo: flow: 50 lbs/min 640cfm .60 Trim Compressor TURBINE SPECS: P-Trim Turbine .96 A/R HOUSING Builder: Turblown.net Garrett T4. http://lh4.ggpht.com/_AMPW4y_H6z4/Sq...2/IMG_1217.JPG Racing Beats cast stainless header flange. https://www.rx8club.com/attachment.p...6&d=1245818116 Now you can see the TUBO !! no more hiding below. https://www.rx8club.com/attachment.p...7&d=1245818116 Exhaust manifold in the works. https://www.rx8club.com/attachment.p...3&d=1245976661 chaos ensuing above! |
4 Attachment(s)
Shot of the header mocked up to the exhaust. The OMP has been removed for space.
https://www.rx8club.com/attachment.p...8&d=1246038709 New exhaust manifold pics as of 7/1/09 https://www.rx8club.com/attachment.p...1&d=1246851286 https://www.rx8club.com/attachment.p...1&d=1246851286 https://www.rx8club.com/attachment.p...1&d=1246851286 New pic 8/23/09 V-band flange attached. https://www.rx8club.com/attachment.p...1&d=1251055612 |
5 Attachment(s)
Possible location for the Turbo. Still deciding on the BEST location to allow correct airflow and minimize turbulence in the intake charge.
https://www.rx8club.com/attachment.p...1&d=1246851626 https://www.rx8club.com/attachment.p...1&d=1246851626 New pics 8/23/09 placement of External WG in relation ship to the manifold https://www.rx8club.com/attachment.p...1&d=1251055834 better shot of the finished welds of the manifold https://www.rx8club.com/attachment.p...1&d=1251055992 |
Saved for pics 4
|
So much for secret squrril Dave LOL
I wish I wasn't moving or I'd have Elliot build me a manifold and dp too |
Yea I know. I'm not going to divulge all the details until its done.
|
FAIL! where are the pics?
|
I demand pics...
|
3 Attachment(s)
A few toys have arrived..
|
pretty nice specs on the turbo..what power levels are you looking to hit?
|
That is a Precision Billet Gt35R. Last time I checked Garrett didn't have the 1.06 T4 framed turbine housing available. We are probably going to go with the .82 T4 turbine housing . I am hoping with a 3.5" down-pipe and open dump waste-gate that the pre-turbine back pressure will be low with that small of a turbine side.. If not then we will just switch back to the original plan of a 1.0 P trim 57trim To4E...
|
AHHHHHHHHHH! I have been thread jacked !
j/k Thanks for tth pics E. As for expected/gestimated power levels, who knows. we will find out when we get there... Now I will say this. I did pick up 65 hp from the Greddy kit. This custom setup blows the doors off the Greddy one in parts alone. Not withstanding the lbs of air that this build will supply at the same psi compared to the Greddy.. |
Very nice, best of luck with your build!
|
o damn wow, looking forward to this, anything special going to be done to the transmission ?
love the look of the top mount turbos. |
Originally Posted by blackenedwings
(Post 3086320)
Very nice, best of luck with your build!
Originally Posted by czar
(Post 3086528)
o damn wow, looking forward to this, anything special going to be done to the transmission ?
love the look of the top mount turbos. Nothing major planed yet for Transmission upgrades. Just better ATF. If Easy_E1 can light up his tires in 1st and make massive clouds of smoke and His still shifts fine and runs smooth. I don't plan on lighting the tires so I should be ok. :ylsuper: |
Good Luck On the build!
|
Looks like its going to be an awesome build. I hope all goes well for you.
|
this is going to be great. i see you're using the rb manifold flange and precision turbo. good call. i will be keeping an eye on this build.
|
Originally Posted by 09Factor
(Post 3072837)
Battery will have to be relocated into the trunk and the AST will be Aluminium.
|
Someone here made 260whp with a 5speed 4 port motor . Hope you can beat that .
How much boost were you pushing with the Greddy for an extra 60hp ? |
Originally Posted by nuke0907
(Post 3086730)
anymore info on this? i was planning on the same thing to open my engine bay up a bit. which ones will you be using?
The current bat is a Yellow top Optima. So I'm not worried about any leakage. I'd be damned if I get stains on the trunk carpet ! :anger:
Originally Posted by Brettus
(Post 3086927)
Someone here made 260whp with a 5speed 4 port motor . Hope you can beat that .
How much boost were you pushing with the Greddy for an extra 60hp ? We saw 202hp @ 7 psi.( i think). The dyno is in my Greddy build thread
Originally Posted by NgoRX8
(Post 3086720)
this is going to be great. i see you're using the rb manifold flange and precision turbo. good call. i will be keeping an eye on this build.
i'll see if I can get more upclose pics of the compressor wheel. I can't any of the credit.. Turblown picked the parts. I just gave him a car to use them on. |
Originally Posted by 09Factor
(Post 3086987)
The batt Relocation is Turblowns own custom setup.
The current bat is a Yellow top Optima. So I'm not worried about any leakage. I'd be damned if I get stains on the trunk carpet ! :anger: |
1 Attachment(s)
321SS Turbo manifold in the works...
|
Originally Posted by Turblown
(Post 3087334)
321SS Turbo manifold in the works...
come to think of it, is it being moved to the trunk? thats the way i want mine. i guess i could just get one of the kits off summit racing or something but i'm not sure what size. i have the same yellow top battery. |
All times are GMT -5. The time now is 09:58 PM. |
© 2024 MH Sub I, LLC dba Internet Brands