Dyno'd my AT
I dyno'd my AT this past weekend at the grand opening of PRT Performance that opened in Lewisville, TX.
2005 4spd on 2nd engine that has 14k miles Performance mods- RB Intake w/ Duct, RB Race Exhaust, RP Midpipe Ignition is crapping out around 5k and higher so it didn't put down the numbers I hoped for but I know I can do better once that is replaced and have another run. It also had to deal with 100+ degree weather here in TX which I know isn't helping. Pull was done in 3rd gear starting at 3500rpm Mustang Dyno numbers 146rwhp and tq. I'm not sure if I'm embedding this video right or not so let me know if you have trouble seeing it- http://px5.sfstatic.com/thumbs/0002/00/84/2300048.jpgMazda RX8 Dyno |
You almost hit my terrible 155RWHP, 118WTQ mark on a 1/2 dead 6port engine.
Video works, I love WWP. How much torque did it put down? |
1 Attachment(s)
Torque is roughly the same as HP, there was a spike on the dyno graph when I was changing gears to get up to speed that threw off the final numbers. The graph says my torque was 190 but I know that's not right.
Attachment 241892 |
Wow. You can really see the huge dump in Mazda's fueling values that happens right at 5500 RPM on the 4-port.
So much torque is lost because of that. |
cobb time?
|
Originally Posted by Bigbacon
(Post 4056869)
cobb time?
Would it fix the problem he is describing? Thanks |
Probably.
It won't likely be a miraculous increase, but you can probably get back that 15 to 25 ft/lbs of torque you lose after 5500 RPM, which you will feel. |
Don't feel too bad about the numbers. The lowest i've seen 137whp. Also nice sparks right after you start to decel.
Yes, get the AP from MickeyMouse, I mean MazdaManiac. It will make a differance thats noticiable. |
PRT Performance in Lewisville?
JTtheDude,
where is PRT at in Lewisville? I live in Lewisville as well. I drive an 05 pearl white Rx8. I just lowered it. I'm usually driving around town on Round Grove and Valley Parkway.
Originally Posted by JTtheDude
(Post 4056809)
I dyno'd my AT this past weekend at the grand opening of PRT Performance that opened in Lewisville, TX.
2005 4spd on 2nd engine that has 14k miles Performance mods- RB Intake w/ Duct, RB Race Exhaust, RP Midpipe Ignition is crapping out around 5k and higher so it didn't put down the numbers I hoped for but I know I can do better once that is replaced and have another run. It also had to deal with 100+ degree weather here in TX which I know isn't helping. Pull was done in 3rd gear starting at 3500rpm Mustang Dyno numbers 146rwhp and tq. I'm not sure if I'm embedding this video right or not so let me know if you have trouble seeing it- http://px5.sfstatic.com/thumbs/0002/00/84/2300048.jpgMazda RX8 Dyno |
I look at it this way...my RX8 is much much faster than the 1995 Integra I was driving. It looks 100 times better, my wife loves it and loves to cruise with me in it, my daughter thinks it has a turbo, it's a definite head-turner, it corners like it's on rails now that it's lowered.
If you're happy with it, who cares about the dyno numbers? It's much lighter than a lot of cars, so just because they have higher horsepower doesn't make them necessarily faster. Enjoy the ride! |
Originally Posted by whiterx8man
(Post 4064408)
JTtheDude,
where is PRT at in Lewisville? I live in Lewisville as well. I drive an 05 pearl white Rx8. I just lowered it. I'm usually driving around town on Round Grove and Valley Parkway. end thread jack/ |
146whp is already pretty good for a NA 4AT. a 3" exhaust might get you a couple more HP but you're likely already at the top.
The first time I dyno'd my 4AT it was at 138whp. After pulling the CAT and replacing with a BB resonated mid pipe I gained about 8 for a whopping 146whp myself. It wasn't until I took drastic measures that things changed significantly. |
Here's the address of PRT Performance, there was a thread in the Regional Forums about it when they opened.
PRT Performance/ Kantuning 1421 N. Cowan Ave Lewisville, Texas |
Originally Posted by MazdaManiac
(Post 4056855)
Wow. You can really see the huge dump in Mazda's fueling values that happens right at 5500 RPM on the 4-port.
So much torque is lost because of that. |
Originally Posted by van
(Post 4079058)
Just wondering, is this common to all 4-Port AT's?
|
How much was it to dyno??
|
Originally Posted by MazdaManiac
(Post 4079067)
Yes.
|
Originally Posted by van
(Post 4079086)
I guess I'll be placing in an order for the COBB AP w/ MMCC soon then :)
https://www.rx8club.com/series-i-engine-tuning-forum-63/new-accessports-free-shipping-1-3-off-price-custom-calibration-service-222986/ |
Originally Posted by MazdaManiac
(Post 4079091)
Do it now and save your self up to 25%! Plus, it'll ship out to you today.
Thanks! |
Originally Posted by Ravioli
(Post 4079077)
How much was it to dyno??
|
what is the COBB AP w/ MMCC please?
|
this is what it is, get one!
http://www.mazdamaniac.com/ |
All times are GMT -5. The time now is 07:55 PM. |
© 2024 MH Sub I, LLC dba Internet Brands