Brettus turbo 111 (the ultimate Renesis turbo ?)
#1827
Hybrid Greddy Boosted
Interesting idea. How are you going to confirm whether you'll be able to safely run more boost? Monitor exhaust temps, check for pulled timing, use knock headphones, use virtual dyno to check whether power is increasing proportionally to boost?
For those interested, see post #12 posted by TeamRX8 on rx-8 injectors:
How does the fuel injection system work?
It looks like injector activation is based on load, and has no direct correlation to aux port opening. If Brettus' mod is effective it would indicate that fuel injector placement in the aux port, and injector activation triggered by port opening may have been a sensible design decision.
For those interested, see post #12 posted by TeamRX8 on rx-8 injectors:
How does the fuel injection system work?
It looks like injector activation is based on load, and has no direct correlation to aux port opening. If Brettus' mod is effective it would indicate that fuel injector placement in the aux port, and injector activation triggered by port opening may have been a sensible design decision.
#1828
I'm not looking at it so much as a way of increasing boost ...... hoping it will make more power on the same boost. If that is the case then yes , it may well have helped make power on an N/A engine if Mazda had put injectors in those runners. Should be able to check it using virtual dyno.
Actually ............ In theory ..... if all settings are kept the same I should be able to tell just by seeing how many g/s it flows . Before vs after.
Actually ............ In theory ..... if all settings are kept the same I should be able to tell just by seeing how many g/s it flows . Before vs after.
Last edited by Brettus; 02-06-2019 at 06:15 PM.
#1829
Did a test tonight .Set it up with a boost switch plus an rpm activated relay . Initially I thought there was no difference but I realised all the w/m was getting sucked out of the line post check valve so........... that is causing a delay in activation . Maybe something good happening once it does activate but need to resolve the issue before confirming.
Really need another check valve so i can mount one on top of each nozzle ...that might solve it .....maybe.
Really need another check valve so i can mount one on top of each nozzle ...that might solve it .....maybe.
Last edited by Brettus; 02-07-2019 at 01:50 AM.
#1830
Registered
iTrader: (2)
With the injectors that close to the rotors, do you think the water content will have sufficient time to vaporize?
Would be interesting to see if you find any difference between the 50-50 mix you’re planning to run and a 100% alcohol supply.
this thread on RX-7 club has some good information.
https://www.rx7club.com/3rd-generati...fd-fix-806104/
Would be interesting to see if you find any difference between the 50-50 mix you’re planning to run and a 100% alcohol supply.
this thread on RX-7 club has some good information.
https://www.rx7club.com/3rd-generati...fd-fix-806104/
#1831
Registered
While I am no expert, I believe even if the water hasn't vaporized by time the motor begins compressing the charge that it will be quickly absorbed once those rotors begin squeezing that mixture down. Since the MSP is 10:1 compression and at 15 psi added (turbo) you are more like 20:1 dynamic compression (294 psi). Compressing the mixture 20 fold will generate so much heat that the water will vaporize well before it comes time to fire the plugs.. Of course, you could always add too much water. I use the same principle to inject directly into the compressor blades of the turbo and the engine itself.
Last edited by strokercharged95gt; 02-07-2019 at 09:31 AM.
The following users liked this post:
Brettus (02-07-2019)
#1832
With the injectors that close to the rotors, do you think the water content will have sufficient time to vaporize?
Would be interesting to see if you find any difference between the 50-50 mix you’re planning to run and a 100% alcohol supply.
this thread on RX-7 club has some good information.
https://www.rx7club.com/3rd-generati...fd-fix-806104/
Would be interesting to see if you find any difference between the 50-50 mix you’re planning to run and a 100% alcohol supply.
this thread on RX-7 club has some good information.
https://www.rx7club.com/3rd-generati...fd-fix-806104/
#1837
Modulated Moderator
iTrader: (3)
I was looking to find a picture to show you why.... ...the alcohol tends to evaporate at a much lower temp than the water.... and when it gets a nice concentration over the hot manifold bad things happen.... ask me how I know....
Where did you mount your pump? I know it's a long way to the trunk..... but it is a lot cooler back there.
I put in a 3 gal fuel cell for the Meth feed tank and mounted the pump under the trunk floor on the right wheel well area.
#1838
Might give up on the idea anyway .
Virtual dyno shows no gains . All I can see from the logs is a gain after the boost cut activates at 7250.
It seems like the cooling effect takes a while to do anything ...heat on the tube maybe?
mass airflow vs rpm with w/m in red without in blue . Have done several runs and see same result each time.
Virtual dyno shows no gains . All I can see from the logs is a gain after the boost cut activates at 7250.
It seems like the cooling effect takes a while to do anything ...heat on the tube maybe?
mass airflow vs rpm with w/m in red without in blue . Have done several runs and see same result each time.
#1839
Registered
I don't think you should really see any gains from adding methanol/water to a system (most lose power). The power comes from additional timing and boost.
On my 11:1 compression mustang I would get tons of knock running more than 6-7 lbs of boost on 93 octane. I changed my head-gasket about 5 times in a span of 18 months. I added a water/methanol injection system with two 5 GPH (315 ml/min) nozzles right before the throttle body, and run about 9 psi on a Precision 7675 and haven't had knock or changed a head-gasket since. Its more of a safety cushion.
On my 11:1 compression mustang I would get tons of knock running more than 6-7 lbs of boost on 93 octane. I changed my head-gasket about 5 times in a span of 18 months. I added a water/methanol injection system with two 5 GPH (315 ml/min) nozzles right before the throttle body, and run about 9 psi on a Precision 7675 and haven't had knock or changed a head-gasket since. Its more of a safety cushion.
#1840
I’m pretty sure we’re seeing the limits of the renny here. Kudos to Brett for throwing the kitchen sink at it.
i think Brett’s earlier conclusion of this motor being limited by exhaust flow to be accurate. I wonder if it would be possible to use the 7’s housing with the 8’s irons? You would have to make a custom mani of course but you would be able to boost the **** off it with that kind of flow no?
i think Brett’s earlier conclusion of this motor being limited by exhaust flow to be accurate. I wonder if it would be possible to use the 7’s housing with the 8’s irons? You would have to make a custom mani of course but you would be able to boost the **** off it with that kind of flow no?
#1841
I don't think you should really see any gains from adding methanol/water to a system (most lose power). The power comes from additional timing and boost.
On my 11:1 compression mustang I would get tons of knock running more than 6-7 lbs of boost on 93 octane. I changed my head-gasket about 5 times in a span of 18 months. I added a water/methanol injection system with two 5 GPH (315 ml/min) nozzles right before the throttle body, and run about 9 psi on a Precision 7675 and haven't had knock or changed a head-gasket since. Its more of a safety cushion.
On my 11:1 compression mustang I would get tons of knock running more than 6-7 lbs of boost on 93 octane. I changed my head-gasket about 5 times in a span of 18 months. I added a water/methanol injection system with two 5 GPH (315 ml/min) nozzles right before the throttle body, and run about 9 psi on a Precision 7675 and haven't had knock or changed a head-gasket since. Its more of a safety cushion.
You can see afr take a dive (as w/m activates) about half way along the log and boost cut just after vert. blue line.
Vs log ran just after with no w/m
Last edited by Brettus; 02-10-2019 at 02:35 PM.
#1843
Registered
Is your rev limiter cut fuel, ignition, or both?
#1845
Registered
Oh gotcha, you turn the duty cycle to 0 above 7,200 or so. So on spring pressure alone you are getting more flow because you are getting slightly more boost.
So you are trying to figure out why your are making slightly more boost on waste-gate pressure alone (while injecting). The richer/denser mixture while injecting meth/water could be putting more volume through the turbine speeding up the turbo enough for a bit more boost. It may just be insignificant. I can do back to back runs in my car with the same tune and get different logs.
So you are trying to figure out why your are making slightly more boost on waste-gate pressure alone (while injecting). The richer/denser mixture while injecting meth/water could be putting more volume through the turbine speeding up the turbo enough for a bit more boost. It may just be insignificant. I can do back to back runs in my car with the same tune and get different logs.
#1846
Hybrid Greddy Boosted
Whenever I've made changes to my setup that result in increased boost at the same WG spring setting, I've observed increased MAF readings and improved exhaust manifold to intake manifold pressure ratio (exhaust pressure may have increased slightly, but the ratio is better). I'd guess that if you measured your exhaust to boost ratio, it would probably confirm improved efficiency. Must be caused by lower exhaust gas temperatures, reducing exhaust back pressure at any given MAF reading under boost, meaning the engine can breath in more air.
I'd run back to back logs with and without w/m injection using WG spring only, so there's no boost cut causing confusion in the logs. At the same time I'd log exhaust manifold back pressure to get a clear Exhaust to boost ratio for comparison.
I'd probably gather another set of logs with duty cycle set to run highest boost without hitting the boost cut. This may show more noticeable differences with and without injection, as the airflow is deeper into the compressor efficiency island.
Another test that takes more effort would be to lock the aux port open the whole time, and rig up the injection so you can switch it on manually. Then gather logs with and without injection switched on. This way you'd get an entire pull with injection without worrying about any lag or w/m pooling as the aux port opens. This would give you more direction on whether the trigger system for the injection is effective.
I'd run back to back logs with and without w/m injection using WG spring only, so there's no boost cut causing confusion in the logs. At the same time I'd log exhaust manifold back pressure to get a clear Exhaust to boost ratio for comparison.
I'd probably gather another set of logs with duty cycle set to run highest boost without hitting the boost cut. This may show more noticeable differences with and without injection, as the airflow is deeper into the compressor efficiency island.
Another test that takes more effort would be to lock the aux port open the whole time, and rig up the injection so you can switch it on manually. Then gather logs with and without injection switched on. This way you'd get an entire pull with injection without worrying about any lag or w/m pooling as the aux port opens. This would give you more direction on whether the trigger system for the injection is effective.
The following users liked this post:
Brettus (02-12-2019)
#1847
The richer/denser mixture while injecting meth/water could be putting more volume through the turbine speeding up the turbo enough for a bit more boost. It may just be insignificant. I can do back to back runs in my car with the same tune and get different logs.
The setup pretty consistent from one run to the next ..... I'm def. seeing that change.
#1848
Since you already have nozzles, and are on your way to Nobels price in research, you might want to try Hydrogen Peroxide(H2O2) in approx 30% concentration. If memory serves me right, it transit into H2O+O at 4-500°C, this requires energy, lowering the temperature, and on top of that you have added an extra O in liquid form(= very dense = just about no of the normal air is displaced = more air at ignition). I'm not sure if the alloys will be able to take H2O2, as it's very reactive with some.
#1849
Did some more w/m injection experimentation with various nozzle sizes and locations .... sadly I didn't find any extra power.
However, I have been giving it some stick on some windy roads and absolutely loving the feel of this setup running at the high 300s level . Power onset is smooth and very controllable.I don't need to rev it very high to have fun. Handling and brakes manage the power with ease. I've never driven a supercar but to me this car feels like one when in that environment.
However, I have been giving it some stick on some windy roads and absolutely loving the feel of this setup running at the high 300s level . Power onset is smooth and very controllable.I don't need to rev it very high to have fun. Handling and brakes manage the power with ease. I've never driven a supercar but to me this car feels like one when in that environment.
The following users liked this post:
RotaryMachineRx (02-28-2019)
#1850
Registered
... However, I have been giving it some stick on some windy roads and absolutely loving the feel of this setup running at the high 300s level . Power onset is smooth and very controllable.I don't need to rev it very high to have fun. Handling and brakes manage the power with ease. I've never driven a supercar but to me this car feels like one when in that environment.