where can i buy this triple gauge pod?
http://i289.photobucket.com/albums/l...et/rx8pod3.jpghttp://i289.photobucket.com/albums/l...et/rx8pod2.jpghttp://i289.photobucket.com/albums/l...et/rx8pod1.jpg i've been on the internet for 4 hours searching for this but i still cant find someone who has them in stock and sells them i've seen some but they look ugly and they cost like $300:banghead: :icon_no2: wtf so can someone help me or redirect me to a thread that i have missed thats answers my question
|
renesisSE3P has a guage pod setup similar to that, ask him :)
|
thanks
|
you can get it at rx8strakes.com
|
^they only sell the lotek type of gauge pod that goes on top, and its more expensive on their site.
http://www.gaugepods.com/mazda.html |
The picture he showed was of the lotek pod... which your right, it does go on top. You can also find it occasionally on e-bay, that is where I got mine.
|
^^ thanks i'll check ebay i dont feel like spending more than $100 on this
|
n rider 89 thanks ima be buying them from there.just wondering what are the clamps for what do you clamp them to?
|
After you remove your center dash piece you need to cut a hole in it. You then glue the pod to it and clamp it down until the clue drys. It will look like this when done.
http://i236.photobucket.com/albums/f...s/4-7-8020.jpg http://i236.photobucket.com/albums/f...s/4-7-8016.jpg |
damn that looks so nice so these gauges do they read for example fuel/voltage w some wire that goes to the source or a signal
|
Originally Posted by rx8speeddmon
(Post 2559557)
After you remove your center dash piece you need to cut a hole in it. You then glue the pod to it and clamp it down until the clue drys. It will look like this when done.
http://i236.photobucket.com/albums/f...s/4-7-8020.jpg http://i236.photobucket.com/albums/f...s/4-7-8016.jpg |
Originally Posted by rx8phase1
(Post 2560466)
hey i just noticed u have something connected to the airbag light
|
yeah on my 8 thats the airbag light for the passenger side it lights up saying airbag off when a certain amount of weight is on it i think if its under a hundred pounds
|
before 06 at least in the states in the it was just a circle in the dash
|
Yes, it is just an accessory plug for the radar detector... haven't gotten around to hard-wiring it yet. The gauges I got are oil pressure, oil temp, and coolant temp. The gauges are from prosport, which many on the site have. I looked at past transactions and lotek on ebay login name is lotekengineering. The gauges are from http://prosportgauges.com/.
|
i would get the voltage/fuel and the third im still deciding our car already has an oil pressure gauge and temp.so what do you guys think my third should be?
|
^ don't rely too much on the stock gauges. they aren't very accurate -- especially the oil pressure gauge
|
^ yeah my oil pressure one has always been in the same place a lil over the middle hopefully thats a good thing lol
|
All that shows is if you've got pressure or not.... I like watching mine bounce up and down w/ the throttle.
|
^ haha thats bada$$ ima get the oil pressure gauge for my third then....one more thing on a scale from 1-5 how hard is the install im asking cuz im afraid of doing anything that includes cutting or making holes in my car
|
For me about a 3. My temperment isn't suited to this time consuming task...... at times I just wanted to use a hammer. It is just basically pulling wires and keeping them straight, but I read through other install threads to find the wires to tap. GL w/ your install.
|
Originally Posted by rx8speeddmon
(Post 2559557)
After you remove your center dash piece you need to cut a hole in it. You then glue the pod to it and clamp it down until the clue drys. It will look like this when done.
http://i236.photobucket.com/albums/f...s/4-7-8020.jpg http://i236.photobucket.com/albums/f...s/4-7-8016.jpg |
All times are GMT -5. The time now is 01:12 AM. |
© 2024 MH Sub I, LLC dba Internet Brands