Pics of my painted badges(and how I did it)
2 Attachment(s)
I decided to paint my badges black after seeing some good photos of dyed ones. Here are some pics of the front and rear badges, the rear mazda one is black too, just not in the picture. I removed the badges with a credit card and a blow dryer, then sanded the badges down for about 5 minutes a piece with a sanding block and then painted with Krylon Black Vinyl Dye spraypaint, about ten very light coats (overkill), and then about three or four coats of clear coat spray paint. I used semi-gloss, I might change it up to glossy, but I am going to get some dark colored rims and I will see how well the colors will match up.
Attachment 271105 Attachment 271106 |
nicely done
|
How did you re-adhere them?
|
Very nice! I did that same procces on stuff on my car... it works really good
|
Originally Posted by Bullitt
(Post 3276105)
How did you re-adhere them?
|
That looks great nice job
|
looks great, after the 4th time i started getting careless with mine and they look shitty now. i gotta completely re-do them and buy a new front emblem.
|
I used a silicon rubbery glue stuff that i found in my Dad's garage. I tried it on an inconspicuous spot and it didn't pull the paint off the car, I'll try to get a picture or name of it, it came in a tube for a caulking gun.
|
Originally Posted by boarderjosh10
(Post 3279481)
I used a silicon rubbery glue stuff that i found in my Dad's garage. I tried it on an inconspicuous spot and it didn't pull the paint off the car, I'll try to get a picture or name of it, it came in a tube for a caulking gun.
|
I have glossy on my SS.... I think it sets it off better, plus i have black Enkei LS-5 wheels
but still looks good!!! |
I think I might go glossy after the winter and see how these hold up
|
its all about flat black :) matches my rims better.
|
Looks good.
|
How does the paint hold up, have you had any chipping or wearing on them, or do they look just as good as when you painted them? Do they hold up in the Car wash?
|
Originally Posted by RotaryMachineRx
(Post 3318698)
How does the paint hold up, have you had any chipping or wearing on them, or do they look just as good as when you painted them? Do they hold up in the Car wash?
|
yea my paint is holding up really well, it rained for about two weeks straight (minnesota fall) and the badges are still fine, I think I am going to see how well they do over winter and then I am going to take them off and repaint them and make them higher gloss, they are not that glossy right now and this was my first attempt so I am sure I can make them look even better.
|
Originally Posted by boarderjosh10
(Post 3320378)
yea my paint is holding up really well, it rained for about two weeks straight (minnesota fall) and the badges are still fine, I think I am going to see how well they do over winter and then I am going to take them off and repaint them and make them higher gloss, they are not that glossy right now and this was my first attempt so I am sure I can make them look even better.
|
looks good. your front emblem's gonna have chip marks in a bout a day or two :) can't really do anything about it.. haha
|
actually the front emblem has been doing pretty well so far, I am going to try and take a picture of the badges again so that people can see what a month in the rain will do to them (not much).
|
Is there holes under the badge on the front bumper or is it adheared on as well?
|
Yes, holes on front.
|
Re: Pics of my painted badges(and how I did it)
Originally Posted by boarderjosh10
(Post 3275977)
I decided to paint my badges black after seeing some good photos of dyed ones. Here are some pics of the front and rear badges, the rear mazda one is black too, just not in the picture. I removed the badges with a credit card and a blow dryer, then sanded the badges down for about 5 minutes a piece with a sanding block and then painted with Krylon Black Vinyl Dye spraypaint, about ten very light coats (overkill), and then about three or four coats of clear coat spray paint. I used semi-gloss, I might change it up to glossy, but I am going to get some dark colored rims and I will see how well the colors will match up.
http://i923.photobucket.com/albums/a...0/IMG_2028.jpg http://i923.photobucket.com/albums/a...0/IMG_2026.jpg |
Hey I want to do this, what did you use to readhere the rx-8 emblem? what kind of tape do you use?
|
I used the thin, black 3M tape. Got it at Pep Boys.
|
Looks good, I did basically the same thing and used pretty much the same as you did.
I left the RX-8 off the back of mine however as I have the RX-8 in the high brake light position...........and as Bullit just said, I also used the Black thin 3M tape to re-adhere them. Oh.............instead of the credit card and blow dryer, just use dental floss! Works like a charm, just kinda use it as a saw as you work your way across. I also think the secret here is quite a few light coats of clear afterwards. Being in sunny, hot, and wet Florida, I know I had to use it and did. Mine have been done for about 8 months and no issues. |
All times are GMT -5. The time now is 11:06 PM. |
© 2024 MH Sub I, LLC dba Internet Brands