|
|
Originally Posted by spicedham
(Post 385909)
Well, I tried doing the CD Hack, and I think i messed up my HU pretty bad. I followed Ectomort's instructions, put everything back together, and then put the HU back in my 3. I tested out the hack but I was only getting audio out of my right channel from my iPod, however, the rest of the stereo was working fine. So I removed the head unit again, took it apart, and tried re-soldering the ground and left channels. I put the HU back in my car, but the unit was dead - no power, nothing lightning up. So I took the HU out again, took it apart, and removed the soldering. Put it back together, and put it back in my car. Now the HU powers up when I turn on my car, the front panel lights work, and the stereo makes the beeping noises when I use try to use the steering wheel controls, but other than that, the HU is still not working. None of the modes (radio, cd) work and the display, though backlit, remains blank (no Hello! message). Any suggestions, or am I going to have to bite the bullet and buy a new HU?
P.S. I tried this hack because I had a long road trip coming up and couldn't wait for Overload's AUX IN module, which I still plan on installing when it becomes available |
I bought this Mazda 3 5mm Earphone Mini Jack Aux in Audio Input Adapter for MP3 Player Phone | eBay, Installed it, but the TAPE/MD button doesnt do anything when pressed. Am I missing something? I have a 2004 Rx8 w/ 6 disc in dash.
|
Originally Posted by CMG
(Post 4507697)
I bought this Mazda 3 5mm Earphone Mini Jack Aux in Audio Input Adapter for MP3 Player Phone | eBay, Installed it, but the TAPE/MD button doesnt do anything when pressed. Am I missing something? I have a 2004 Rx8 w/ 6 disc in dash.
This cable is 120cm long with Mazda connector on one end and 3.5mm male headphone jack inputs on the other. Play your music through your Mazda head unit (must have CD changer input on the back of car radio). Just plug one end of this cable into the CD changer input in the back of your stereo and the other end to the mini jack input on the device. You can't connect a CD Changer to the head unit at the same time while this cable is connected. Control and display remain on the audio device -- the Mazda headunit will NOT control or display text. |
Originally Posted by G-ReX
(Post 4508510)
That's why the Auxmod is a more complicated/expensive solution (but a good one).
|
cassette hack - Mazda6
Hello, I have Mazda6 2002 with cassette player and no CD, and would like to make AUX input from this cassette.
But do knot now what and how. I can not see any pictures in the thread, do not know why. I have registered into the forum, but still no pictures. Could you help and give me some advice? My email address is martin.joch@seznam.cz I have tried to fool the cassette deck, took one cassette, took out everything from inside - tape, wheels, etc. but the cassette deck is somehow smart, it did find out and wrote: CHECK TAPE. The second try was to close the tape drawer as a cessette is inside, and I have disconnected both motors, but it wrote: NO TAPE. This japanese piece of electronic is somehow smart. Thank you very much. Martin |
Originally Posted by bluegoof
(Post 4814733)
Hello, I have Mazda6 2002 with cassette player and no CD, and would like to make AUX input from this cassette.
But do knot now what and how. I can not see any pictures in the thread, do not know why. I have registered into the forum, but still no pictures. Could you help and give me some advice? My email address is martin.joch@seznam.cz I have tried to fool the cassette deck, took one cassette, took out everything from inside - tape, wheels, etc. but the cassette deck is somehow smart, it did find out and wrote: CHECK TAPE. The second try was to close the tape drawer as a cessette is inside, and I have disconnected both motors, but it wrote: NO TAPE. This japanese piece of electronic is somehow smart. Thank you very much. Martin |
8 Attachment(s)
Here are the pictures of what I did.
I follow the instructions that appears on whatmyip.org On the picture page 14 you will find the terminal solder where the job need to be done. You will see a Left Audio, Right Audio and Shared Ground. I buy the 3.5mm Aux cable with the female jack. I cut off the white connector and solder the cable to the Left Audio, Right Audio and Shared Ground. (Please see the pictures). To the Left Audio, the cable that need to be solder from the white connector is the white cable. To the Right Audio, the cable that need to be solder from the white connector is the yellow cable. To the Shared Ground, the cable that need to be solder from the white connector is the red cable. After that I resemble the radio back and install it in the car. Please follow the whatmyip.org instructions. Then I run the 3.5 Aux cable underside the center console until the rear box. I remove the lighter, drill the plastic and put the female jack. (Please see the pictures). Put a "Silence CD" into the radio and play the music from your phone. And that's all. |
From where did you buy the tape player and how much. Tnx...
|
Originally Posted by Ristov
(Post 4890608)
From where did you buy the tape player and how much. Tnx...
|
| All times are GMT -5. The time now is 07:08 PM. |
© 2024 MH Sub I, LLC dba Internet Brands