DIY: Chargespeed Fender Vents Install
DIY: My Chargespeed Fender Vents.
http://i107.photobucket.com/albums/m...espeed_001.jpg There are 3 screws to remove to get to the stock vents http://i107.photobucket.com/albums/m...espeed_002.jpg Need a flexible hand like mine :) http://i107.photobucket.com/albums/m...espeed_003.jpg The stock vents are held by 6 clips. Just need to press them with your fingers from the inside http://i107.photobucket.com/albums/m...espeed_004.jpg Circled in red are the clips http://i107.photobucket.com/albums/m...espeed_005.jpg Here's how the fender looks like without the vents http://i107.photobucket.com/albums/m...espeed_006.jpg Test Fit the Chargespeed Fender Vents first to get the position of the hole. Yes need to drill hole...2 holes to be precise http://i107.photobucket.com/albums/m...espeed_007.jpg Mark the position of the holes with a pen or something sharp http://i107.photobucket.com/albums/m...espeed_008.jpg Drill away. Make sure the drill bit is the correct size otherwise ...big trouble http://i107.photobucket.com/albums/m...espeed_009.jpg Here's how the holes look like - circled in red http://i107.photobucket.com/albums/m...espeed_010.jpg Put a little grease on the holes to prevent rust. Paint would be better. http://i107.photobucket.com/albums/m...espeed_011.jpg Screw the Chargespeed Fender Vents on. Don't forget to put back the 3 screws taken off earlier in step 2 http://i107.photobucket.com/albums/m...espeed_012.jpg Taa Daa.... DIY Chargespeed Fender Vents install... http://i107.photobucket.com/albums/m...espeed_013.jpg |
nice
|
tada! finally... :)
|
Does it help with downforce, or is it just cosmetic?
|
nice, but i like your wheels more haha
|
Thanks guys. Believe it's both cosmetic and helps a little with directing the airflow too. Since the stock vents were just a mesh design, this one has a directional air vent...
|
were did you get them from , link????
|
^^ Yeah, what he said
BTW, they look great! |
|
Originally Posted by Goober8
(Post 2240274)
|
how much did they cost? i couldnt tell on the website...
|
the vents aren't functional because there is no opening from the engine bay to have the air flow through it.
i was looking at these a while back, they do look good, but in one of your pics it seems like the vent holes don't completely cover the metal across the vent hole. |
look good. got some pics from further away? not sure on the shape. i got some from a vendor here than more mimic the stock look (i can't think of the name of the company) but w/ the mesh behind the openings -- look good but the fitment wasn't great.
|
Guys, Some new pics. I made some in Carbon fibre. It looks better than the FRP ones. Enjoy:)
See photos below. http://i107.photobucket.com/albums/m...espeed_014.jpg http://i107.photobucket.com/albums/m...espeed_015.jpg http://i107.photobucket.com/albums/m...espeed_016.jpg http://i107.photobucket.com/albums/m...espeed_017.jpg http://i107.photobucket.com/albums/m...espeed_018.jpg http://i107.photobucket.com/albums/m...espeed_019.jpg http://i107.photobucket.com/albums/m...espeed_020.jpg |
All times are GMT -5. The time now is 12:27 PM. |
© 2024 MH Sub I, LLC dba Internet Brands