hymee screens
anyone have the directions?
i got them used a couple of years ago. i am finally replacing an oil cooler and would like to put them in. i also dont have the hardware, but i am sure i can find something that will work. but the directions would make it easy!!! beers :beer: |
They just slip onto the tabs that hold the shrouds in place....I don't remember even getting any instructions with mine??
|
Originally Posted by dannobre
(Post 2590083)
They just slip onto the tabs that hold the shrouds in place....I don't remember even getting any instructions with mine??
that makes a lot of sense!!! i think the center screen is the one that is the trick.. btw, you fuel stuff under control? i had black goo. ;) beers :beer: |
They go behind the fogs...right up against the coolers.
Pull the bumper...the front screen goes over the lower opening...and you use the small screws on the marked squares in the mesh to hold it on. If I pull my bumper tomorrow I'll take a couple of pictures for you Got the fuel system done...but it won't crank....I had a mouse under the hood...hope it didn't chew up too much....going to have to trace wires tomorrow and see what's up :( |
Originally Posted by dannobre
(Post 2590191)
They go behind the fogs...right up against the coolers.
Pull the bumper...the front screen goes over the lower opening...and you use the small screws on the marked squares in the mesh to hold it on. If I pull my bumper tomorrow I'll take a couple of pictures for you Got the fuel system done...but it won't crank....I had a mouse under the hood...hope it didn't chew up too much....going to have to trace wires tomorrow and see what's up :( beer :beer: |
the hymee screens go right on the coolers, under the rubber "shrouds"
I'll see if i can find my instructions tomorrow |
Originally Posted by laythor
(Post 2590201)
the hymee screens go right on the coolers, under the rubber "shrouds"
I'll see if i can find my instructions tomorrow a photo of that.. beers :beer: |
Originally Posted by swoope
(Post 2590197)
i have most of a wiring harness if you need it.
beer :beer: I have the whole day tomorrow with no distractions ( like kids :) ) so I should know by the end of the day :) I also have a transmission leak?? Seems to be coming from the seam by the drain...might have to swap in the new tranny I have sitting in the garage. Good time to install the BHR clutch and flywheel as welll..... |
Originally Posted by swoope
(Post 2590202)
ahhhhhh.
a photo of that.. you'll see in the first and third photos that it's held in place by the rubber shroud, the shroud just peels off second photo show how the screen is held in the middle by screws coming up through the tabs, if you dont have screws with your kit just use zip screws from the AC section of any home store beers :beer: http://i43.photobucket.com/albums/e3...s/DSCF1105.jpg http://i43.photobucket.com/albums/e3...s/DSCF1104.jpg http://i43.photobucket.com/albums/e3...s/DSCF1103.jpg |
Dani have a complete harness if you want it---sell it cheap. pm me.
olddragger |
Figured it out, and it was the first thing I checked for a change :) ....clutch interlock switch.....wired it closed and it started right up.
Now I just have to look at the tranny leak :lol: |
thanks all.
got it on this after noon.. and glad you got it fixed dan.. beers :beer: |
so did you get your shiny new BHR radiator installed, scott?
|
Originally Posted by chickenwafer
(Post 2591937)
so did you get your shiny new BHR radiator installed, scott?
and i did not get the sways or endlinks in. or raise the rear by .5" the garage had a bad karma weekend.. i am just happy to have gotten the new oil cooler and screens in.. the guy that puts the oil cooler line bolts in is stronger than the oil filter guy. :lol: another thing that did not happen was getting the remote oil cooler in.. got to find an adapter for between the plate and the oil sensor. the sensor is to small for the orifice in the plate. any hints would be nice. damn i am needy all of a sudden! :) round two this weekend.. beers :beer: |
[QUOTE=laythor;2590212]those i do have
thx, i would love to have had the screws for the bottom. but i made something work.. and a note. that stuff fits good! beers :beer: |
hey swoope, why did ya replace ur oil cooler anyway?
|
All times are GMT -5. The time now is 09:19 AM. |
© 2024 MH Sub I, LLC dba Internet Brands