RX8Club.com - Search Results

Notices
 
Search: Posts Made By: niteshade247
Showing results 1 to 50 of 486
Search took 0.22 seconds.
12-20-2014, 04:41 PM
Replies: 14
Views: 601
Posted By niteshade247

Here you go

Here you go
12-18-2014, 10:57 AM
Replies: 9
Views: 702
Posted By niteshade247

Make sure you got the wires in the right place...

Make sure you got the wires in the right place too. It's a easy mistake.
12-16-2014, 12:45 AM
Replies: 14
Views: 601
Posted By niteshade247

First rule if you don't think or know it was done...

First rule if you don't think or know it was done and it's at the milage it needs it assume it hasn't been done and do it. First on the list (if you didn't do it before you bought it) compression...
12-15-2014, 07:17 PM
Replies: 12
Views: 538
Posted By niteshade247

Replace or rebuild the engine is the only true...

Replace or rebuild the engine is the only true fix for failing compression. Cost can be from $2500-$6000 depending on who you have build it,how meany parts are reusable,and if you take the engine out...
12-14-2014, 12:47 AM
Replies: 10
Views: 1,964
Posted By niteshade247

Make sure you get the flywheel reserficed right...

Make sure you get the flywheel reserficed right and be ready for the 54mm nut holding it on. One other thing there is a pilot bearing seal that goes in after the pilot bearing make sure you get one...
12-14-2014, 12:30 AM
Replies: 3
Views: 470
Posted By niteshade247

Yup green turned me onto the ultra gauge too....

Yup green turned me onto the ultra gauge too. Love the thing and for what it does for the cost you can beat it.
12-13-2014, 01:21 AM
Replies: 1
Views: 1,133
Posted By niteshade247

Possible RX9 on the board

Recently I seen the new rotary engine mazda has been working on. This prompted me to start searching for info on the car they might put it in and found this. Personally if they do put a electric...
12-04-2014, 09:05 AM
Replies: 18
Views: 611
Posted By niteshade247

Me and myster were talking to legot about his...

Me and myster were talking to legot about his comment. As for the bottle just keep in mind when you go to change it latter the it is quite easy to snap the nipple off the rad and once that happens...
12-03-2014, 09:39 PM
Replies: 18
Views: 611
Posted By niteshade247

You did what? ^

You did what? ^
12-03-2014, 03:51 PM
Replies: 18
Views: 611
Posted By niteshade247

I would advise a new coolant bottle to go with it...

I would advise a new coolant bottle to go with it so you have no weak points in the cooling system.
12-03-2014, 10:43 AM
Replies: 7
Views: 623
Posted By niteshade247

Flashing CEL is misfire. Change coils wires and...

Flashing CEL is misfire. Change coils wires and plugs. You've had it for a year and unless you have paper work to show the last time coils have been changed assume they haven't been. Coils last about...
12-03-2014, 08:46 AM
Replies: 12
Views: 628
Posted By niteshade247

Approximately 4 liters to a gallon so your...

Approximately 4 liters to a gallon so your getting 16 MPG if your doing all city driving than that's just about right ( might be 2 or 3 MPG lower than normal). It's not low enough I'd think you have...
12-03-2014, 08:31 AM
Replies: 18
Views: 611
Posted By niteshade247

( scatches head) so do you have a auto tranny or...

( scatches head) so do you have a auto tranny or a MT? If you've got a MT why are you screwing around with a rad that's not even suppost to be on the car? If it is a auto you've got biger problems...
11-30-2014, 05:52 PM
Replies: 24
Views: 5,751
Posted By niteshade247

Just a shot in the dark but pull the shifter and...

Just a shot in the dark but pull the shifter and check to see if it's truly in nutral. It's possible you or some one els put it in gear when installing the shifter and now it's out of line. Only...
11-30-2014, 05:37 PM
Replies: 38
Views: 2,229
Posted By niteshade247

CAT failure will only show after you have started...

CAT failure will only show after you have started damiging your engine full coil failure will only show after damiging the CAT. if coils are showing signes of starting to fail and notheing is done...
11-30-2014, 12:13 PM
Replies: 11
Views: 842
Posted By niteshade247

Glad to hear.

Glad to hear.
11-30-2014, 12:12 PM
Replies: 24
Views: 5,751
Posted By niteshade247

Rapid clinking could be low battery or terminals...

Rapid clinking could be low battery or terminals need cleaned and to be better secured.
11-29-2014, 05:18 PM
Replies: 11
Views: 842
Posted By niteshade247

You need to do both resets to gather or risk...

You need to do both resets to gather or risk other problems. It will idle like crap and could stall first couple of starts but that's normal. You'll just have to drive about 50-100 miles for it to...
11-29-2014, 05:04 PM
Replies: 38
Views: 2,229
Posted By niteshade247

Lots of rotary shops around your area take it...

Lots of rotary shops around your area take it there NOT some tire shop. If your not that good with cars take lots of pics as you work so you have a reference latter when putting it back together. 70%...
11-29-2014, 01:26 PM
Replies: 11
Views: 842
Posted By niteshade247

The valve doesn't close compleatly but it...

The valve doesn't close compleatly but it shouldn't be open more than a small crack. It's possible you didn't get the TB back on tight or it's not sealed right. Mine idles around 800 RPMs after it's...
11-29-2014, 09:06 AM
Replies: 7
Views: 751
Posted By niteshade247

Blue with white stripe and red with yellow stripe.

Blue with white stripe and red with yellow stripe.
11-29-2014, 08:29 AM
Replies: 7
Views: 751
Posted By niteshade247

Give me a few minutes I'll go snap a shot for you.

Give me a few minutes I'll go snap a shot for you.
11-29-2014, 08:27 AM
Replies: 18
Views: 1,135
Posted By niteshade247

With 3 bad coils I'd check the CAT it could have...

With 3 bad coils I'd check the CAT it could have been damiged and a damiged CAT can kill your engine.
11-29-2014, 08:18 AM
Replies: 38
Views: 2,229
Posted By niteshade247

Use OEM coils only. No eBay no auto zone...

Use OEM coils only. No eBay no auto zone specials. The only other coils that can be used are LS1 ( I forget the numbers) but this swap can be riddled with problems or BHR coils (these I have and...
11-28-2014, 11:29 PM
Replies: 7
Views: 450
Posted By niteshade247

I'm not seeing your saying you have start...

I'm not seeing your saying you have start problems just that it's cutting out on you so I don't know why some one would tell you your started is bad. Once the car is running the starter has nothing...
11-28-2014, 11:03 PM
Replies: 38
Views: 2,229
Posted By niteshade247

Premixing won't boost compression ether unless...

Premixing won't boost compression ether unless your poring it in at really high amounts. Premixing is for safety to keep from engine failure due to OMP failure as well as better lubricant to the...
11-28-2014, 03:23 PM
Replies: 38
Views: 2,229
Posted By niteshade247

I wasn't trying to be a ass and glad you really...

I wasn't trying to be a ass and glad you really didn't take it like that. Just have respect for the car it's no 500HP vett but it can still hurt you and others as soon as you think have it under...
11-28-2014, 11:48 AM
Replies: 18
Views: 1,135
Posted By niteshade247

A few things come to mind 1 dirty MAF. 2 dirty...

A few things come to mind 1 dirty MAF. 2 dirty ESS. 3 ECU was not correctly cleared after new engine. 4 bad CAT.
11-28-2014, 11:36 AM
Replies: 7
Views: 653
Posted By niteshade247

Lucas semi here too.

Lucas semi here too.
11-28-2014, 11:32 AM
Replies: 18
Views: 2,411
Posted By niteshade247

Rotary resurrection has a eBay page and has lots...

Rotary resurrection has a eBay page and has lots of parts might even give you some tips on your rebuild. I agree with the others don't cheap out on parts this is no piston engine one cheap part can...
11-28-2014, 09:50 AM
Replies: 7
Views: 751
Posted By niteshade247

Haven't striped the inside of my car like that...

Haven't striped the inside of my car like that but I have had enough out to say that the pic above is correct for the left drive body.
11-28-2014, 09:40 AM
Replies: 38
Views: 2,229
Posted By niteshade247

Sorry to tell you this but I have never met a 17...

Sorry to tell you this but I have never met a 17 year old that could drive for shit (this includes my self at that age) and assuming that you can is going to get you in trouble (not trying to bash...
11-27-2014, 12:41 PM
Replies: 6
Views: 1,639
Posted By niteshade247

I put one on my 8 when I put my mid pipe on. It...

I put one on my 8 when I put my mid pipe on. It made me pull a 420 code. Pulled it off and 420 code went away no codes shown at all now.
11-27-2014, 12:35 PM
Replies: 11
Views: 529
Posted By niteshade247

TDX stage 4 in mine been on for 2 years no...

TDX stage 4 in mine been on for 2 years no trouble here. The only thing with it is it's so beefy first gear can be tricky.
11-23-2014, 11:05 PM
Replies: 11
Views: 1,431
Posted By niteshade247

The basics are the same as far as I know. If you...

The basics are the same as far as I know. If you can put a 7 engine together I would think you could do an 8. But the changes come in when moding the engine there are huge differences.
11-23-2014, 10:55 PM
Replies: 15
Views: 591
Posted By niteshade247

Don't count on the dealer knowing much more than...

Don't count on the dealer knowing much more than Firestone in fact they might know less.
11-21-2014, 10:40 PM
Replies: 11
Views: 597
Posted By niteshade247

I see you said "cutting out at hight RPM...

I see you said "cutting out at hight RPM (beeping)" well that's normal there is a fuel cut off around that time to keep you from killing the engine. Don't hit the fuel cut off to much as it's not...
11-21-2014, 10:31 PM
Replies: 11
Views: 1,431
Posted By niteshade247

Port locations is one big difference. How the...

Port locations is one big difference. How the roter moves is another. In porting the cooling area is so close to the exhaust port one slip and your done new housing time. Point is yes it a rotary but...
11-20-2014, 09:37 PM
Replies: 101
Views: 7,984
Posted By niteshade247

Face palm. He still just don't get it. All the...

Face palm. He still just don't get it. All the things we have told him and all the times he was wrong. No matter what we say this kid just ain't going to listen. So I'm going to leave him to FUBR his...
11-20-2014, 02:51 PM
Replies: 101
Views: 7,984
Posted By niteshade247

Seeing how the OMP failed and most likely caused...

Seeing how the OMP failed and most likely caused the engine problem the housings are scared so put 2 new housing on the list untill you open it up to find out for sure.
11-20-2014, 09:14 AM
Replies: 30
Views: 1,945
Posted By niteshade247

Did you prime the line? Do some looking into...

Did you prime the line? Do some looking into premixing as if you have one of the other lines brake having some premix in the tank is better than running with a dry oiling system. Any safety measure...
11-20-2014, 08:57 AM
Replies: 9
Views: 555
Posted By niteshade247

The only wires I can see coming from that...

The only wires I can see coming from that location is the APV motor and the SSV switch. Here is a diagram for you to look over. Your fuel injectors are under there too so give them a check.
11-19-2014, 08:52 PM
Replies: 5
Views: 557
Posted By niteshade247

All your inquiry's are valid but one. The...

All your inquiry's are valid but one. The drilling of a 3rd oil port you could spend more than what the car is worth to get a 3rd to work (remember your trying to add two new oiling ports not just...
11-19-2014, 08:44 PM
Replies: 9
Views: 555
Posted By niteshade247

I'll look tomorrow at my car and let you know...

I'll look tomorrow at my car and let you know where it goes
11-19-2014, 08:41 PM
Replies: 55
Views: 7,151
Posted By niteshade247

Good laugh for all. I bought a baby bottle to...

Good laugh for all. I bought a baby bottle to measure out then mix some gas up before putting it in the tank so it mixes better and not just coat the inside of the pipe going to the tank.
11-19-2014, 08:36 PM
Replies: 30
Views: 2,108
Posted By niteshade247

I've had my coolant sensor disconnected for 3...

I've had my coolant sensor disconnected for 3 years and it's never made my CEL come on. Yes the immobilizer blinking when the key is not in the ignition and car is off is normal this indicates it is...
11-18-2014, 05:49 PM
Replies: 55
Views: 7,151
Posted By niteshade247

Supper teck is twc 3.

Supper teck is twc 3.
11-17-2014, 10:09 PM
Replies: 101
Views: 7,984
Posted By niteshade247

Keep us posted

Keep us posted
11-17-2014, 09:10 PM
Replies: 101
Views: 7,984
Posted By niteshade247

Was fuel pressure checked under load?

Was fuel pressure checked under load?
11-17-2014, 09:07 PM
Replies: 10
Views: 604
Posted By niteshade247

If $85 is all you got to pay for a new engine and...

If $85 is all you got to pay for a new engine and all the work I'd pay and not risk pissing some one off and getting a piss poor install.
Showing results 1 to 50 of 486
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.