{ FS } Rx8 part out Series 1 heavily Modded
10-21-2017, 10:00 PM
#1
Rx8 part out Series 1 heavily Modded
Category: Engine - Complete Motors
Price: $100
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): Series I, Series II
Location (US State/Canada/Int): IL
Item Condition: Used
BHR ign $275 (sold)
Spare tire kit $175 shipped (without tire)
rx8 series 1 axles $50 each prefer local pick up
Mazmart oil pressure regulator kit $25 shipped
Rotor housings $75 a piece plus shipping
Kyle Mohan ported side housings (non-bridge port) $150 a piece shipped
Stock Tapped oil pan for turbo set up has 5/8" I.D. welded bung for a barb fitting $75 shipped
I have 2 front engine covers with OMP's on them $100 a piece shipped
2 Pairs of weight C front and rear rotors $100 a piece plus shipping. Has oil control rings on them
2 Front covers $30 + shipping
2 intake manifolds and 2 extension manifolds. $50 a piece
Nav unit with center console $280 shipped
Head lights $120 each shipped they are the factory HID and will come with the wiring.
(Driver side sold)
Tail lights $85 shipped each
I have a hood $100 local pick up only
Trunk lid w/o spoiler $100 local pick up only
Driver side front Door $150 Local Pick up only (Passenger side sold)
Suicide doors $75 a piece Local Pick up only.
Last edited by jtizzle88; 01-29-2018 at 02:45 PM.
10-22-2017, 09:53 PM
#12
shortly after changing out the shitty injectors about 100 or so miles later 1 apex seal blew. I had a set of ra super seals. I tore the engine down today one of the front rotor apex seals was dark like it was getting burned up and smashed toward the tip. Will have to show picture to better explain it. I have gone through several rebuilds and over 4 years with it.
Parting out so I can have some money to build my speed 6 so I can have some real power to play with.
I'm very sad and hate to do this. I will get back in rotary either a series 2 with engine swap or an fc.
Parting out so I can have some money to build my speed 6 so I can have some real power to play with.
I'm very sad and hate to do this. I will get back in rotary either a series 2 with engine swap or an fc.
The following users liked this post:
jtizzle88 (10-23-2017)
10-23-2017, 08:43 AM
#15
Yes the cooling fan kit is still available so is the mishimoto tstat. They work perfect together. My cooling temps never reached over 190 degrees. Really hot day it may hit 201 or so but it cools back down to 180 once the fans are engaged. Winter time you will average 169-174 but still get great cabin heat.
11-04-2017, 08:47 AM
#23
how much for the wheels and tires? If you have a sunroof I would be interested in the overhead console with switches, the exhaust trim from rear bumper, and drivers headlight assembly? If the trans is good I might be interested in that too. My 2nd gear synchro is shot. ,
11-04-2017, 04:28 PM
#24
The console $150, Exhaust trim $25, my headlights are factory HID $175 for the LH.
Wheels and tires are good just need to be rebalanced since the sticky wheel weights came off. $300 fro the whole set if interested. Local pick up only if you want to go the route with shipping then you would have to be willing to absorb the cost for shipping.
11-04-2017, 05:40 PM
#25
I am looking for panel with reading lamps and sunroof switches. I am in Kansas City but will be going to Michigan in the near future. I would have made a special trip for trans and wheels but don't need the wheels as badly as I need the trans. When I go through next time I will check on to see what you might have left.